Swalesilver soil
Wild-clay potential
Strong lead
Strong lead: a clayey layer typically about 5 to 18 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Swalesilver soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Swalesilver spot on the map
Rated from the USDA soil survey record for Swalesilver loam, 0 to 1 percent slopes (Upper Deschutes River Area, Oregon, Parts of Deschutes, Jefferson, and Klamath Counties) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 55% clay in the fine-earth portion.
- Raises the potential High engineering plasticity index (35): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil moderately sticky and very plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 13 in (33 cm)).
- Note Typically starts within about 5 in (13 cm) of the surface.
- Missing data Rock fragment content is not reported.
- Note High shrink-swell (linear extensibility about 7.5%): often very plastic, and prone to cracking as it dries.
- Note Engineering class CH: a clay of high plasticity in the Unified system.
Layer by layer
- Loamy layerH1 A loam layer about 0 to 3 in down: about 20% clay, low plasticity when wet, very pale brown when moist. Weak indication
- Sandy layerH2 A silt loam layer about 3 to 5 in down: about 8% clay, low plasticity when wet, light gray when moist. Weak indication
- Clay-rich layerH3best layer A clay layer about 5 to 18 in down: about 55% clay, high plasticity when wet, light brownish gray when moist. Strong lead
- Loamy layerH4 A silty clay loam layer about 18 to 40 in down: about 32% clay, moderate plasticity when wet, light gray when moist. Promising
- Loamy layerH5 A clay loam layer about 40 to 50 in down: about 32% clay, moderate plasticity when wet, light gray when moist. Promising
- Loamy layerH6 A loam layer about 50 to 60 in down: about 22% clay, moderate plasticity when wet, pale yellow when moist. Weak indication
What it looks like raw
The clay-rich layer (H3), 5 to 18 in down in the typical profile: light brownish gray (10YR 6/2), grayish brown (10YR 5/2) moist; hard, firm, moderately sticky and very plastic. Raw colour is not fired colour.
About the soil
- Parent material: lacustrine deposits.
- USDA family mineralogy: smectitic. Smectite-rich clays are usually very plastic and shrink a lot as they dry.
- USDA family particle-size class: fine.
- Drainage: somewhat poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 3 map units in Oregon, in these survey areas: Harney County Area, Oregon; Lake County, Oregon, Northern Part, Parts of Lake and Klamath Counties; Upper Deschutes River Area, Oregon, Parts of Deschutes, Jefferson, and Klamath Counties.
By state: wild clay in Oregon.
USDA, distribution and extent: South-central Oregon. These soils are moderately extensive. MLRA 23.
USDA, geographic setting: Swalesilver soils are on depressions on plateaus and lake terraces. These soils formed in alluvium and lacustrine deposits derived from volcanic rocks and volcanic ash. Slopes are 0 to 2 percent. Elevation ranges from 1,280 to 1,910 meters. The climate is characterized by cold, moist winters and warm, dry summers. The mean annual temperature is 4 to 7 degrees C, mean annual precipitation is 200 to 300 mm, and the frost-free period is 50 to 90 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Moonbeam: Strong lead
- Alyan: Strong lead
- Chancelakes: Strong lead
- Connleyhills: Strong lead
- Hayespring: Strong lead
- Overallflat: Strong lead
- Silverash: Strong lead
- Ninemile: Promising
See it on the map
Open a Swalesilver spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 90%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Swalesilver loam, 0 to 1 percent slopes, map unit 149A in Upper Deschutes River Area, Oregon, Parts of Deschutes, Jefferson, and Klamath Counties.
- Official Series Description: Swalesilver(revised 06/2011), established.
- Taxonomic class: Fine, smectitic, frigid Aquic Palexeralfs
- Rated with rule version 2026-09-28.1; the method is on the About page.