Silverash soil
Wild-clay potential
Strong lead
Strong lead: a clay-enriched layer typically about 8 to 21 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Silverash soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Silverash spot on the map
Rated from the USDA soil survey record for Silverash ashy fine sandy loam, 0 to 1 percent slopes (Lake County, Oregon, Northern Part, Parts of Lake and Klamath Counties) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 48% clay in the fine-earth portion.
- Note USDA labels this a "Bt" horizon: a subsoil layer where clay has accumulated.
- Raises the potential High engineering plasticity index (35): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil moderately sticky and very plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 13 in (33 cm)).
- Note Typically starts within about 8 in (20 cm) of the surface.
- Missing data Rock fragment content is not reported.
- Note High shrink-swell (linear extensibility about 8%): often very plastic, and prone to cracking as it dries.
- Note Engineering class CH: a clay of high plasticity in the Unified system.
Layer by layer
- TopsoilA An ashy fine sandy loam layer about 0 to 2 in down: about 14% clay, moderate plasticity when wet, pale brown when moist. Weak indication
- TopsoilAE An ashy loam layer about 2 to 8 in down: about 16% clay, moderate plasticity when wet, light brownish gray when moist. Weak indication
- Clay subsoilBtbest layer A clay layer about 8 to 21 in down: about 48% clay, high plasticity when wet, light brown when moist. Strong lead
- Loamy layerC A sandy clay loam layer about 21 to 62 in down: about 24% clay, moderate plasticity when wet, light brownish gray when moist. Possible
What it looks like raw
The clay subsoil (Bt), 8 to 21 in down in the typical profile: light brown (7.5YR 6/3), brown (7.5YR 4/2) moist; very hard, very firm, moderately sticky and very plastic. Raw colour is not fired colour.
About the soil
- Parent material: volcanic ash mixed with lacustrine and alluvial deposits derived from mixed volcanic rock.
- USDA family mineralogy: smectitic. Smectite-rich clays are usually very plastic and shrink a lot as they dry.
- USDA family particle-size class: fine.
- Drainage: poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Oregon, in these survey areas: Lake County, Oregon, Northern Part, Parts of Lake and Klamath Counties.
By state: wild clay in Oregon.
USDA, distribution and extent: South-central Oregon. These soils are not extensive with about 7,300 acres of the series mapped to date. MLRA 23.
USDA, geographic setting: Silverash soils are on depressions on plateaus and lakebeds. These soils formed in alluvium and lacustrine deposits derived from volcanic rocks and volcanic ash. Slopes are 0 to 2 percent. Elevation ranges from 1,310 to 1,580 meters. The climate is characterized by cold, moist winters and warm, dry summers. The mean annual temperature is 6 to 7 degrees C, mean annual precipitation is 200 to 300 mm, and the frost-free period is 50 to 80 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Alyan: Strong lead
- Chancelakes: Strong lead
- Connleyhills: Strong lead
- Hayespring: Strong lead
- Moonbeam: Strong lead
- Overallflat: Strong lead
- Swalesilver: Strong lead
- Brabble: Promising
See it on the map
Open a Silverash spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Silverash ashy fine sandy loam, 0 to 1 percent slopes, map unit 619 in Lake County, Oregon, Northern Part, Parts of Lake and Klamath Counties.
- Official Series Description: Silverash(revised 06/2011), established.
- Taxonomic class: Fine, smectitic, frigid Aquandic Palexeralfs
- Rated with rule version 2026-09-28.1; the method is on the About page.