Alyan soil
Wild-clay potential
Strong lead
Strong lead: a clay-enriched layer typically about 11 to 23 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Alyan soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Alyan gravelly sandy loam, 3 to 15 percent slopes (Lake County, Oregon, Northern Part, Parts of Lake and Klamath Counties) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 37% clay in the fine-earth portion.
- Note USDA labels this a "Bt" horizon: a subsoil layer where clay has accumulated.
- Raises the potential High engineering plasticity index (25): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil very sticky and very plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 12 in (30 cm)).
- Note Typically starts within about 11 in (28 cm) of the surface.
- Note Few rock fragments (about 0% by volume).
- Note High shrink-swell (linear extensibility about 7.5%): often very plastic, and prone to cracking as it dries.
- Note Engineering class CH: a clay of high plasticity in the Unified system.
Layer by layer
- TopsoilA1 A gravelly sandy loam layer about 0 to 3 in down: about 16% clay, moderate plasticity when wet, grayish brown when moist. Weak indication
- TopsoilA2 A sandy clay loam layer about 3 to 11 in down: about 21% clay, moderate plasticity when wet, dark grayish brown when moist. Possible
- Clay subsoilBtbest layer A clay loam layer about 11 to 23 in down: about 37% clay, high plasticity when wet, brown when moist. Strong lead
- BedrockR Bedrock about 23 to 33 in down: no clay layer to dig. Weak indication
What it looks like raw
The clay subsoil (Bt), 11 to 23 in down in the typical profile: brown (10YR 5/3), dark brown (10YR 3/3) moist; hard, firm, very sticky and very plastic. Raw colour is not fired colour.
About the soil
- Parent material: residuum and colluvium derived from volcanic rock such as welded tuff, basalt, or rhyolite.
- USDA family mineralogy: smectitic. Smectite-rich clays are usually very plastic and shrink a lot as they dry.
- USDA family particle-size class: fine.
- Drainage: well drained.
- Lithic bedrock typically about 23 in (58 cm) down.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Oregon, in these survey areas: Harney County Area, Oregon; Lake County, Oregon, Northern Part, Parts of Lake and Klamath Counties.
By state: wild clay in Oregon.
USDA, distribution and extent: Northern Nevada and south-central Oregon. These soils are moderately extensive. The series concept and main acreage is in MLRA 25, while other acreage occurs in MLRA 24 in Nevada and MLRA 23 in Oregon.
USDA, geographic setting: Alyan soils are on hills, mountains, and plateaus. They occur on all slope positions. These soils formed in residuum and colluvium derived from volcanic rocks. Slopes are 2 to 50 percent. Elevations range from 1,525 to 2,290 meters in Nevada to as low as 1,280 meters in Oregon. The climate is semiarid with cool, moist winters and warm, dry summers. The mean annual precipitation is 250 to 360 mm, mean annual temperature is 6 to 7 degrees C, and the frost-free period is typically 70 to 100 days, but may range down to 50 days in Oregon.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Moonbeam: Strong lead
- Swalesilver: Strong lead
- Chancelakes: Strong lead
- Connleyhills: Strong lead
- Hayespring: Strong lead
- Overallflat: Strong lead
- Silverash: Strong lead
- Gradon: Promising
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Alyan gravelly sandy loam, 3 to 15 percent slopes, map unit 202 in Lake County, Oregon, Northern Part, Parts of Lake and Klamath Counties.
- Official Series Description: Alyan(revised 02/2016), established.
- Taxonomic class: Fine, smectitic, frigid Aridic Argixerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.