Donlonton soil
Wild-clay potential
Possible
Possible: a clay-enriched layer typically about 9 to 30 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Donlonton soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Donlonton spot on the map
Rated from the USDA soil survey record for Donlonton fine sandy loam, 2 to 5 percent slopes (Charles County, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 21% clay. It may need settling or refining to become a clay body.
- Note USDA labels this a "Bt" horizon: a subsoil layer where clay has accumulated.
- Note Moderate engineering plasticity index (10).
- Note Thick enough to investigate (about 21 in (53 cm)).
- Note Typically starts within about 9 in (23 cm) of the surface.
- Note Few rock fragments (about 10% by volume).
Layer by layer
- TopsoilAp A fine sandy loam layer about 0 to 9 in down: about 10% clay, low plasticity when wet, olive brown when moist. Weak indication
- Clay subsoilBtbest layer A sandy clay loam layer about 9 to 30 in down: about 21% clay, moderate plasticity when wet, olive brown when moist. Possible
- Sandy layerBCg A fine sandy loam layer about 30 to 41 in down: about 12% clay, low plasticity when wet, olive brown when moist. Weak indication
- Sandy layerCBjg A loamy fine sand layer about 41 to 67 in down: about 7% clay, low plasticity when wet, dark olive green when moist. Weak indication
What it looks like raw
The clay subsoil (Bt), 9 to 30 in down in the typical profile: olive brown (2.5Y 4/4). Raw colour is not fired colour.
About the soil
- Parent material: glauconitic loamy fluviomarine deposits.
- USDA family mineralogy: glauconitic.
- USDA family particle-size class: fine-loamy.
- Drainage: moderately well drained.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Maryland, in these survey areas: Charles County, Maryland.
By state: wild clay in Maryland.
USDA, distribution and extent: Maryland and New Jersey (major land resource area 149). The series is of small extent.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Lenni: Strong lead
- Magnolia: Strong lead
- Elkton: Promising
- Liverpool: Promising
- Nanticoke: Promising
- Piccowaxen: Promising
- Beltsville: Possible
- Collington: Possible
See it on the map
Open a Donlonton spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 60%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Donlonton fine sandy loam, 2 to 5 percent slopes, map unit DnB in Charles County, Maryland.
- Official Series Description: Donlonton(revised 11/2015), established.
- Taxonomic class: Fine-loamy, glauconitic, mesic Aquic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.