Beltsville soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 25 to 50 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Beltsville soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Beltsville spot on the map
Rated from the USDA soil survey record for Beltsville silt loam, 0 to 8 percent slopes (District of Columbia) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 25% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (11.5).
- Note Thick enough to investigate (about 25 in (63 cm)).
- Note Typically starts about 25 in (64 cm) down; expect real digging or look for cuts and banks.
- Note Few rock fragments (about 10% by volume).
Layer by layer
- Sandy layerH1 A silt loam layer about 0 to 14 in down: about 14% clay, low plasticity when wet, yellowish brown when moist. Weak indication
- Loamy layerH2 A silt loam layer about 14 to 25 in down: about 25% clay, moderate plasticity when wet, yellowish brown when moist. Possible
- Loamy layerH3best layer A silt loam layer about 25 to 50 in down: about 25% clay, moderate plasticity when wet, light brown when moist. Possible
- Loamy layerH4 A sandy loam layer about 50 to 72 in down: about 20% clay, moderate plasticity when wet, variegated yellowish red when moist. Weak indication
What it looks like raw
The loamy layer (H3), 25 to 50 in down in the typical profile: light brown (7.5YR 6/4); very firm. Raw colour is not fired colour.
About the soil
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: moderately well drained.
Where it is mapped
Seen on the map as the most common soil in 31 map units in District of Columbia, Maryland, Pennsylvania, Virginia, in these survey areas: Baltimore County, Maryland; Cecil County, Maryland; Charles County, Maryland; Delaware County, Pennsylvania; District of Columbia; Fairfax County, Virginia; Harford County Area, Maryland; Harford County, Aberdeen Proving Ground, Maryland; Prince George's County, Maryland.
By state: wild clay in District of Columbia,wild clay in Maryland,wild clay in Pennsylvania,wild clay in Virginia.
USDA, geographic setting: Landscape: Coastal plain, upland
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Christiana: Strong lead
- Montalto: Strong lead
- Watchung: Strong lead
- Lenni: Strong lead
- Magnolia: Strong lead
- Benevola: Strong lead
- Cumberstone: Strong lead
- Dunning: Strong lead
See it on the map
Open a Beltsville spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Beltsville silt loam, 0 to 8 percent slopes, map unit BdB in District of Columbia.
- Official Series Description: Beltsville(revised 11/2015), established.
- Taxonomic class: Fine-loamy, mixed, semiactive, mesic Typic Fragiudults
- Rated with rule version 2026-09-28.1; the method is on the About page.