Benevola soil
Wild-clay potential
Strong lead
Strong lead: a clay-enriched layer typically about 8 to 33 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Benevola soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Benevola spot on the map
Rated from the USDA soil survey record for Benevola silt loam, 0 to 3 percent slopes (Baltimore County, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 45% clay in the fine-earth portion.
- Note USDA labels this a "Bt1,Bt2" horizon: a subsoil layer where clay has accumulated.
- Raises the potential High engineering plasticity index (21): USDA's estimate suggests plastic behavior when wet.
- Note Thick enough to investigate (about 25 in (64 cm)).
- Note Typically starts within about 8 in (20 cm) of the surface.
- Note Few rock fragments (about 5% by volume).
- Note Engineering class CH: a clay of high plasticity in the Unified system.
Layer by layer
- TopsoilAp A silt loam layer about 0 to 8 in down: about 26% clay, moderate plasticity when wet, percent dark brown when moist. Possible
- Clay subsoilBt1,Bt2best layer A clay layer about 8 to 33 in down: about 45% clay, high plasticity when wet, percent dark reddish brown when moist. Strong lead
- Clay subsoilBt3,Bt4 A clay layer about 33 to 57 in down: about 45% clay, high plasticity when wet, percent yellowish red when moist. Strong lead
- Clay-rich layerC1, C2,C3 A clay layer about 57 to 115 in down: about 45% clay, high plasticity when wet, percent reddish black when moist. Promising
What it looks like raw
The clay subsoil (Bt1,Bt2), 8 to 33 in down in the typical profile: percent dark reddish brown (2.5YR 3/4); friable. Raw colour is not fired colour.
About the soil
- Parent material: clayey residuum weathered from marble.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Maryland, in these survey areas: Baltimore County, Maryland.
By state: wild clay in Maryland.
USDA, distribution and extent: Maryland, Pennsylvania and possibly Virginia. (major land resource area 148). The series is of small extent.
USDA, geographic setting: The Benevola soils have developed in from residuum from marble. Slopes range from 0 to 25 percent. The climate is temperate and moderately humid, with a mean annual temperature of 45 to 55 degrees F., and mean annual precipitation of 35 to 45 inches.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Christiana: Strong lead
- Cumberstone: Strong lead
- Jackland: Strong lead
- Montalto: Strong lead
- Watchung: Strong lead
- Baile: Promising
- Baltimore: Promising
- Chillum: Promising
See it on the map
Open a Benevola spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Benevola silt loam, 0 to 3 percent slopes, map unit BgA in Baltimore County, Maryland.
- Official Series Description: Benevola(revised 07/2001), established.
- Taxonomic class: Fine, mixed, semiactive, mesic Mollic Hapludalfs
- Rated with rule version 2026-09-28.1; the method is on the About page.