Cumberstone soil
Wild-clay potential
Strong lead
Strong lead: a clayey layer typically about 33 to 54 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Cumberstone soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Cumberstone spot on the map
Rated from the USDA soil survey record for Cumberstone silt loam, 0 to 2 percent slopes (Baltimore County, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 39% clay in the fine-earth portion.
- Note Moderate engineering plasticity index (15).
- Raises the potential The official series description calls the wet soil moderately sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 21 in (53 cm)).
- Note Typically starts about 33 in (84 cm) down; expect real digging or look for cuts and banks.
- Note Few rock fragments (about 1% by volume).
- Note Surface layer; expect roots and organic matter.
Layer by layer
- TopsoilAp A silt loam layer about 0 to 9 in down: about 22% clay, moderate plasticity when wet, olive brown when moist. Weak indication
- Clay subsoilBt A silty clay loam layer about 9 to 23 in down: about 34% clay, moderate plasticity when wet, yellowish brown when moist. Promising
- Sandy layerBCg A silt loam layer about 23 to 33 in down: about 17% clay, low plasticity when wet, light brownish gray when moist. Weak indication
- Clay-rich layer2Agbbest layer A clay loam layer about 33 to 54 in down: about 39% clay, moderate plasticity when wet, dark gray when moist. Strong lead
- Clay subsoil2Btgb A clay layer about 54 to 62 in down: about 41% clay, high plasticity when wet, very dark grayish brown when moist. Promising
- Clay-rich layer2BCgb A sandy clay layer about 62 to 72 in down: about 37% clay, moderate plasticity when wet, olive gray when moist. Promising
What it looks like raw
The clay-rich layer (2Agb), 33 to 54 in down in the typical profile: dark gray (2.5Y 4/1); firm, moderately sticky, moderately plastic. Raw colour is not fired colour.
About the soil
- Parent material: silty eolian deposits over loamy and clayey fluviomarine deposits.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-silty.
- Drainage: somewhat poorly drained.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Maryland, in these survey areas: Baltimore County, Maryland.
By state: wild clay in Maryland.
USDA, geographic setting: Landscape: Coastal Plain
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Benevola: Strong lead
- Christiana: Strong lead
- Jackland: Strong lead
- Montalto: Strong lead
- Watchung: Strong lead
- Baile: Promising
- Baltimore: Promising
- Chillum: Promising
See it on the map
Open a Cumberstone spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Cumberstone silt loam, 0 to 2 percent slopes, map unit CrA in Baltimore County, Maryland.
- Official Series Description: Cumberstone(revised 11/2015), established.
- Taxonomic class: Fine-silty, mixed, active, mesic Aquic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.