Piccowaxen soil
Wild-clay potential
Promising
Promising: a clay-enriched layer typically about 28 to 56 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Piccowaxen soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Piccowaxen spot on the map
Rated from the USDA soil survey record for Piccowaxen loam, 0 to 2 percent slopes (Charles County, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 37% clay in the fine-earth portion.
- Note USDA labels this a "Btg2" horizon: a subsoil layer where clay has accumulated.
- Note Moderate engineering plasticity index (15).
- Note The official series description calls the wet soil moderately sticky and slightly plastic.
- Note Thick enough to investigate (about 28 in (71 cm)).
- Note Typically starts about 28 in (71 cm) down; expect real digging or look for cuts and banks.
- Note Few rock fragments (about 0% by volume).
- Missing data Held at "Promising" because no plasticity evidence is available; a high clay percentage alone does not make a strong lead.
Layer by layer
- TopsoilA A loam layer about 0 to 4 in down: about 9% clay, low plasticity when wet, very dark grayish brown when moist. Weak indication
- Clay subsoilBt A silt loam layer about 4 to 16 in down: about 12% clay, low plasticity when wet, percent light yellowish brown when moist. Weak indication
- Clay subsoilBtg1 A silt loam layer about 16 to 28 in down: about 23% clay, moderate plasticity when wet, percent light brownish gray when moist. Possible
- Clay subsoilBtg2best layer A clay loam layer about 28 to 56 in down: about 37% clay, moderate plasticity when wet, percent light brownish gray when moist. Promising
- Loamy layer2BCg A fine sandy loam layer about 56 to 72 in down: about 18% clay, low plasticity when wet, gray when moist. Weak indication
What it looks like raw
The clay subsoil (Btg2), 28 to 56 in down in the typical profile: percent light brownish gray (2.5Y 6/2), percent light olive brown (2.5Y 5/3); friable, moderately sticky, slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: silty and loamy fluviomarine deposits.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-silty.
- Drainage: somewhat poorly drained.
Where it is mapped
Seen on the map as the most common soil in 5 map units in Maryland, in these survey areas: Charles County, Maryland; Prince George's County, Maryland.
By state: wild clay in Maryland.
USDA, distribution and extent: Distribution: Coastal Plain of Southern Maryland; possibly the Delmarva Peninsula.
USDA, geographic setting: Landscape: Coastal Plain
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Lenni: Strong lead
- Magnolia: Strong lead
- Christiana: Strong lead
- Howell: Strong lead
- Elkton: Promising
- Liverpool: Promising
- Nanticoke: Promising
- Aquasco: Promising
See it on the map
Open a Piccowaxen spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 80%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Piccowaxen loam, 0 to 2 percent slopes, map unit PcA in Charles County, Maryland.
- Official Series Description: Piccowaxen(revised 06/2007), established.
- Taxonomic class: Fine-silty, mixed, semiactive, mesic Aquic Hapludalfs
- Rated with rule version 2026-09-28.1; the method is on the About page.