Aquasco soil
Wild-clay potential
Promising
Promising: a loamy layer with some clay typically about 44 to 80 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Aquasco soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Aquasco spot on the map
Rated from the USDA soil survey record for Aquasco silt loam, 0 to 2 percent slopes (Cecil County, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clay-enriched layer: about 29% clay in the fine-earth portion.
- Note Moderate engineering plasticity index (13).
- Raises the potential The official series description calls the wet soil moderately sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 36 in (91 cm)).
- Note Typically starts about 44 in (112 cm) down; expect real digging or look for cuts and banks.
- Missing data Rock fragment content is not reported.
Layer by layer
- TopsoilA A silt loam layer about 0 to 4 in down: about 15% clay, low plasticity when wet, black when moist. Weak indication
- Sandy layerE A silt loam layer about 4 to 10 in down: about 14% clay, low plasticity when wet, light yellowish brown when moist. Weak indication
- Clay subsoilBt A silty clay loam layer about 10 to 20 in down: about 29% clay, moderate plasticity when wet, light olive brown when moist. Promising
- Clay subsoilBtx A loam layer about 20 to 44 in down: about 23% clay, moderate plasticity when wet, light olive brown when moist. Possible
- Loamy layerBCtbest layer A clay loam layer about 44 to 80 in down: about 29% clay, moderate plasticity when wet, yellowish brown when moist. Promising
What it looks like raw
The loamy layer (BCt), 44 to 80 in down in the typical profile: yellowish brown (10YR 5/8); clay loam; friable, sticky, plastic. Raw colour is not fired colour.
About the soil
- Parent material: silty eolian deposits over loamy fluviomarine deposits.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-silty.
- Drainage: somewhat poorly drained.
Where it is mapped
Seen on the map as the most common soil in 5 map units in Maryland, in these survey areas: Cecil County, Maryland; Prince George's County, Maryland.
By state: wild clay in Maryland.
USDA, geographic setting: Landscape: Coastal Plain, upland
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Christiana: Strong lead
- Lenni: Strong lead
- Howell: Strong lead
- Magnolia: Strong lead
- Montalto: Strong lead
- Watchung: Strong lead
- Chillum: Promising
- Elkton: Promising
See it on the map
Open a Aquasco spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Aquasco silt loam, 0 to 2 percent slopes, map unit AqA in Cecil County, Maryland.
- Official Series Description: Aquasco(revised 11/2015), established.
- Taxonomic class: Fine-silty, mixed, semiactive, mesic Aquic Fragiudults
- Rated with rule version 2026-09-28.1; the method is on the About page.