Collington soil
Wild-clay potential
Possible
Possible: a clay-enriched layer typically about 10 to 34 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Collington soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Collington spot on the map
Rated from the USDA soil survey record for Collington and Annapolis soils, 10 to 15 percent slopes (Charles County, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 22% clay. It may need settling or refining to become a clay body.
- Note USDA labels this a "Bt" horizon: a subsoil layer where clay has accumulated.
- Note Moderate engineering plasticity index (10).
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 24 in (61 cm)).
- Note Typically starts within about 10 in (25 cm) of the surface.
- Note Few rock fragments (about 11% by volume).
Layer by layer
- TopsoilAp A fine sandy loam layer about 0 to 10 in down: about 16% clay, low plasticity when wet, brown when moist. Weak indication
- Clay subsoilBtbest layer A sandy clay loam layer about 10 to 34 in down: about 22% clay, moderate plasticity when wet, yellowish brown when moist. Possible
- Sandy layerBC A fine sandy loam layer about 34 to 72 in down: about 18% clay, low plasticity when wet, olive when moist. Weak indication
What it looks like raw
The clay subsoil (Bt), 10 to 34 in down in the typical profile: yellowish brown (10YR 5/4); friable; slightly sticky, slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: glauconite bearing loamy fluviomarine deposits.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 15 map units in Maryland, in these survey areas: Cecil County, Maryland; Charles County, Maryland; Prince George's County, Maryland.
By state: wild clay in Maryland.
USDA, distribution and extent: Distribution: Northern Atlantic Coastal Plain of New Jersey, Delaware, and Maryland
USDA, geographic setting: Landscape: Northern Atlantic Coastal Plain
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Lenni: Strong lead
- Christiana: Strong lead
- Magnolia: Strong lead
- Howell: Strong lead
- Montalto: Strong lead
- Watchung: Strong lead
- Elkton: Promising
- Nanticoke: Promising
See it on the map
Open a Collington spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 45%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Collington and Annapolis soils, 10 to 15 percent slopes, map unit CAD in Charles County, Maryland.
- Official Series Description: Collington(revised 11/2015), established.
- Taxonomic class: Fine-loamy, mixed, active, mesic Typic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.