Zen soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 7 to 18 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Zen soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Zen silt loam, 8 to 15 percent slopes (Chelan County Area, Washington (Parts of Chelan and Kittitas Counties)) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 25% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (10).
- Note The official series description calls the wet soil nonsticky and slightly plastic.
- Note Moderate thickness (about 11 in (28 cm)).
- Note Typically starts within about 7 in (18 cm) of the surface.
- Note Few rock fragments (about 5% by volume).
Layer by layer
- Sandy layerH1 A silt loam layer about 0 to 7 in down: about 15% clay, moderate plasticity when wet, brown when moist. Weak indication
- Loamy layerH2best layer A silt loam layer about 7 to 18 in down: about 25% clay, moderate plasticity when wet, yellowish brown when moist. Possible
- Loamy layerH3 A silt loam layer about 18 to 24 in down: about 25% clay, moderate plasticity when wet, yellowish brown when moist. Weak indication
- BedrockH4 Unweathered bedrock about 24 to 34 in down: no clay layer to dig. Weak indication
What it looks like raw
The loamy layer (H2), 7 to 18 in down in the typical profile: yellowish brown (10YR 5/4) dry, dark brown (10YR 3/3) moist; slightly hard, friable, nonsticky and slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: loess and slope alluvium over basalt.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
- Lithic bedrock typically about 24 in (61 cm) down.
Where it is mapped
Seen on the map as the most common soil in 5 map units in Washington, in these survey areas: Chelan County Area, Washington (Parts of Chelan and Kittitas Counties).
By state: wild clay in Washington.
USDA, distribution and extent: Central Washington; MLRA 8; moderately extent
USDA, geographic setting: Elevation--460 to 1000 m
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bjork: Promising
- Peoh: Promising
- Cowiche: Possible
- Morical: Possible
- Anatone: Weak indication
- Ardenvoir: Weak indication
- Beverly: Weak indication
- Billyridge: Weak indication
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Zen silt loam, 8 to 15 percent slopes, map unit ZeC in Chelan County Area, Washington (Parts of Chelan and Kittitas Counties).
- Official Series Description: Zen(revised 09/2019), established.
- Taxonomic class: Fine-loamy, mixed, superactive, mesic Calciargidic Argixerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.