Morical soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 23 to 37 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Morical soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Morical spot on the map
Rated from the USDA soil survey record for Morical fine sandy loam, 3 to 15 percent slopes (Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clay-enriched layer: about 30% clay in the fine-earth portion.
- Note Moderate engineering plasticity index (15).
- Raises the potential The official series description calls the wet soil moderately sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 14 in (36 cm)).
- Note Typically starts within about 23 in (58 cm) of the surface.
- Lowers the potential Noticeable rock fragments (about 16% by volume); screening would be needed and the clay percentage applies to the fine earth only.
Layer by layer
- Sandy layerH1 An ashy fine sandy loam layer about 0 to 12 in down: about 8% clay, low plasticity when wet, grayish brown when moist. Weak indication
- Sandy layerH2 A sandy loam layer about 12 to 23 in down: about 10% clay, low plasticity when wet, brown when moist. Weak indication
- Loamy layerH3best layer A sandy clay loam layer about 23 to 37 in down: about 30% clay, moderate plasticity when wet, light yellowish brown when moist. Possible
- BedrockH4 Weathered bedrock about 37 to 47 in down: no clay layer to dig. Weak indication
What it looks like raw
The loamy layer (H3), 23 to 37 in down in the typical profile: light yellowish brown (10YR 6/4), yellowish brown (10YR 5/4) moist; hard, very firm, sticky and moderately plastic. Raw colour is not fired colour.
About the soil
- Parent material: residuum and colluvium from granitic rock, mixed in the surface with volcanic ash and loess.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
- Paralithic bedrock typically about 37 in (94 cm) down.
Where it is mapped
Seen on the map as the most common soil in 8 map units in Washington, in these survey areas: Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties; Chelan County Area, Washington (Parts of Chelan and Kittitas Counties).
By state: wild clay in Washington.
USDA, distribution and extent: Northeastern Washington; MLRAs 6, 8, and 9. The series is of moderate extent.
USDA, geographic setting: Morical soils are on ridgetops, mountain slopes, and foothills. Slopes are 0 to 90 percent. They formed in residuum and colluvium mixed with volcanic ash and loess in the surface overlying weathered granite or quartzite lithology. Elevation is 2,000 to 3,200 feet. The climate is characterized by warm, dry summers and cool, moist winters. The mean annual precipitation is 12 to 18 inches. The mean January temperature is about 25 degrees F. and the mean July temperature is about 68 degrees F. The mean annual air temperature is 45 to 50 degrees F. The frost-free season is about 100 to 140 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bjork: Promising
- Cle Elum: Promising
- Peoh: Promising
- Cowiche: Possible
- Dragoon: Possible
- Georgecreek: Possible
- Kingmont: Possible
- Loneridge: Possible
See it on the map
Open a Morical spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 80%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Morical fine sandy loam, 3 to 15 percent slopes, map unit 188 in Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties.
- Official Series Description: Morical(revised 02/2011), established.
- Taxonomic class: Fine-loamy, mixed, superactive, mesic Vitrandic Argixerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.