Ardenvoir soil
Wild-clay potential
Weak indication
Weak indication: no layer of Ardenvoir shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Ardenvoir soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Ardenvoir spot on the map
Rated from the USDA soil survey record for Ardenvoir stony fine sandy loam, 30 to 60 percent slopes (Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 8% clay.
- Lowers the potential Low engineering plasticity index (2.5): little plastic behavior expected when wet.
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 44 in (112 cm)).
- Note Typically starts within about 12 in (30 cm) of the surface.
- Lowers the potential High rock content (about 61% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
Layer by layer
- Sandy layerH1 A stony ashy fine sandy loam layer about 0 to 6 in down: about 8% clay, low plasticity when wet, brown when moist. Weak indication
- Sandy layerH2 A very cobbly ashy sandy loam layer about 6 to 12 in down: about 8% clay, low plasticity when wet, light yellowish brown when moist. Weak indication
- Sandy layerH3best layer An extremely gravelly coarse sandy loam layer about 12 to 56 in down: about 8% clay, low plasticity when wet, very pale brown when moist. Weak indication
- BedrockH4 Unweathered bedrock about 56 to 60 in down: no clay layer to dig. Weak indication
What it looks like raw
The sandy layer (H3), 12 to 56 in down in the typical profile: very pale brown (10YR 7/4), yellowish brown (10YR 5/4) moist; slightly hard, friable, slightly sticky and slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: residuum and colluvium weathered from gneiss and schist mixed in the surface with loess and volcanic ash.
- USDA family particle-size class: loamy-skeletal.
- Drainage: well drained.
- Lithic bedrock typically about 56 in (142 cm) down.
Where it is mapped
Seen on the map as the most common soil in 3 map units in Washington, in these survey areas: Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties; Chelan County Area, Washington (Parts of Chelan and Kittitas Counties).
By state: wild clay in Washington.
USDA, distribution and extent: Northern Idaho and eastern Washington; MLRA 43A, 9 and 6. This soil is moderately extensive.
USDA, geographic setting: Ardenvoir soils are on mountains and foothills. Slope ranges from 5 to 90 percent. They occupy all aspects at lower elevations, but mainly occupy southerly aspects at higher elevations. They formed in residuum and colluvium weathered from metasedimentary bedrock, predominantly siltite and fine grained quartzite with a mantle of loess and minor amounts of volcanic ash. Elevation ranges from 2,200 to 5,100 feet (670 to 1555 meters). The mean annual air temperature ranges from 42 to 46 degrees F. and the mean annual precipitation ranges from 18 to 35 inches (483 to 889 mm). The frost-free period is from 80 to 120 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bjork: Promising
- Cle Elum: Promising
- Peoh: Promising
- Cowiche: Possible
- Morical: Possible
- Dragoon: Possible
- Georgecreek: Possible
- Kingmont: Possible
See it on the map
Open a Ardenvoir spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 80%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Ardenvoir stony fine sandy loam, 30 to 60 percent slopes, map unit 32 in Cashmere Mountain Area, Washington, Parts of Chelan and Okanogan Counties.
- Official Series Description: Ardenvoir(revised 06/2013), established.
- Taxonomic class: Loamy-skeletal, isotic, frigid Vitrandic Haploxerepts
- Rated with rule version 2026-09-28.1; the method is on the About page.