Beverly soil
Wild-clay potential
Weak indication
Weak indication: no layer of Beverly shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Beverly soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Beverly spot on the map
Rated from the USDA soil survey record for Beverly fine sandy loam (Chelan County Area, Washington (Parts of Chelan and Kittitas Counties)) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 3% clay.
- Lowers the potential Low engineering plasticity index (0): little plastic behavior expected when wet.
- Lowers the potential The official series description calls the wet soil nonsticky and nonplastic.
- Note Thick enough to investigate (about 36 in (91 cm)).
- Note Typically starts about 24 in (61 cm) down; expect real digging or look for cuts and banks.
- Lowers the potential High rock content (about 52% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
Layer by layer
- Sandy layerH1 A fine sandy loam layer about 0 to 17 in down: about 8% clay, low plasticity when wet, stratified light brownish gray when moist. Weak indication
- Sandy layerH2 An extremely gravelly sandy loam layer about 17 to 24 in down: about 7% clay, low plasticity when wet, pale brown when moist. Weak indication
- Sandy layerH3best layer An extremely gravelly loamy coarse sand layer about 24 to 60 in down: about 3% clay, low plasticity when wet. Weak indication
What it looks like raw
The sandy layer (H3), 24 to 60 in down in the typical profile: loose, nonsticky and nonplastic. Raw colour is not fired colour.
About the soil
- Parent material: alluvium.
- USDA family mineralogy: mixed.
- USDA family particle-size class: sandy-skeletal.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 3 map units in Washington, in these survey areas: Chelan County Area, Washington (Parts of Chelan and Kittitas Counties).
By state: wild clay in Washington.
USDA, distribution and extent: Eastern Washington. It is of moderate extent.
USDA, geographic setting: Beverly soils are on low terraces and fans and have slopes of 0 to 25 percent. They formed in recent gravelly and cobbly mixed alluvium. Elevations are 600 to 1800 feet. The climate is semiarid and has hot dry summers and moist, cold winters. Mean annual precipitation is 8 to 12 inches. Average January temperature is 23 to 25 degrees F.; average July temperature is 70 to 75 degrees F; and the mean annual temperature is about 50 degrees F. The frost-free season is about 140 to 190 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bjork: Promising
- Peoh: Promising
- Cowiche: Possible
- Morical: Possible
- Zen: Possible
- Anatone: Weak indication
- Ardenvoir: Weak indication
- Billyridge: Weak indication
See it on the map
Open a Beverly spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Beverly fine sandy loam, map unit Be in Chelan County Area, Washington (Parts of Chelan and Kittitas Counties).
- Official Series Description: Beverly, established.
- Taxonomic class: Sandy-skeletal, mixed, mesic Xeric Torrifluvents
- Rated with rule version 2026-09-28.1; the method is on the About page.