Walla Walla soil
Wild-clay potential
Weak indication
Weak indication: no layer of Walla Walla shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Walla Walla soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Walla Walla spot on the map
Rated from the USDA soil survey record for Walla Walla silt loam, 40 to 55 percent slopes (Garfield County Area, Washington) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 14% clay.
- Lowers the potential Low engineering plasticity index (2.5): little plastic behavior expected when wet.
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 27 in (69 cm)).
- Note Typically starts within about 17 in (43 cm) of the surface.
- Note Few rock fragments (about 4% by volume).
Layer by layer
- Sandy layerH1 A silt loam layer about 0 to 17 in down: about 14% clay, low plasticity when wet, grayish brown when moist. Weak indication
- Sandy layerH2best layer A silt loam layer about 17 to 44 in down: about 14% clay, low plasticity when wet, brown when moist. Weak indication
- Sandy layerH3 A silt loam layer about 44 to 60 in down: about 14% clay, low plasticity when wet, pale brown when moist. Weak indication
What it looks like raw
The sandy layer (H2), 17 to 44 in down in the typical profile: brown (10YR 5/3) dry, brown (10YR 4/3) moist; slightly hard, friable, slightly sticky and slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: silty eolian deposits.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-silty.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Washington, in these survey areas: Garfield County Area, Washington.
By state: wild clay in Washington.
USDA, distribution and extent: Southeastern Washington and northeastern Oregon; MLRA 8; large extent
USDA, geographic setting: Elevation--45 to 795 m
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bolicker: Weak indication
- Chard: Weak indication
- Gwin: Weak indication
- Lickskillet: Weak indication
- Linville: Weak indication
- Bellingham: Strong lead(same state)
- Cloverland: Strong lead(same state)
- Garfield: Strong lead(same state)
See it on the map
Open a Walla Walla spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Walla Walla silt loam, 40 to 55 percent slopes, map unit WwF in Garfield County Area, Washington.
- Official Series Description: Walla Walla(revised 09/2019), established.
- Taxonomic class: Coarse-silty, mixed, superactive, mesic Typic Haploxerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.