Cloverland soil
Wild-clay potential
Strong lead
Strong lead: a clayey layer typically about 37 to 50 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Cloverland soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Cloverland spot on the map
Rated from the USDA soil survey record for Cloverland silt loam, 8 to 30 percent slopes (Asotin County Area, Washington (Asotin and Garfield Counties)) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 35% clay in the fine-earth portion.
- Raises the potential High engineering plasticity index (20): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil moderately sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 13 in (33 cm)).
- Note Typically starts about 37 in (94 cm) down; expect real digging or look for cuts and banks.
- Note Few rock fragments (about 10% by volume).
Layer by layer
- Loamy layerH1 A silt loam layer about 0 to 6 in down: about 20% clay, moderate plasticity when wet, dark grayish brown when moist. Possible
- Loamy layerH2 A silt loam layer about 6 to 10 in down: about 20% clay, moderate plasticity when wet, grayish brown when moist. Weak indication
- Loamy layerH3 A silt loam layer about 10 to 37 in down: about 26% clay, moderate plasticity when wet, brown when moist. Possible
- Clay-rich layerH4best layer A silty clay loam layer about 37 to 50 in down: about 35% clay, high plasticity when wet, brown when moist. Strong lead
- Clay-rich layerH5 A very cobbly clay loam layer about 50 to 56 in down: about 35% clay, high plasticity when wet, brown when moist. Weak indication
- BedrockH6 Unweathered bedrock about 56 to 60 in down: no clay layer to dig. Weak indication
What it looks like raw
The clay-rich layer (H4), 37 to 50 in down in the typical profile: brown (10YR 5/3), brown (10YR 4/3) moist; very hard, firm, sticky and plastic. Raw colour is not fired colour.
About the soil
- Parent material: loess with a minor amount of slope alluvium derived from weathered basalt and volcanic ash.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-silty.
- Drainage: moderately well drained.
- Lithic bedrock typically about 56 in (142 cm) down.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Washington, in these survey areas: Asotin County Area, Washington (Asotin and Garfield Counties).
By state: wild clay in Washington.
USDA, distribution and extent: Mountainous areas of southeastern Washington and northeastern Oregon; MLRA 9. The series is of small extent.
USDA, geographic setting: Cloverland soils are on mountain plateaus, benches, and north facing hillslopes, and have slopes of 2 to 45 percent. These soils formed in loess and minor amounts of materials weathered from basalt and volcanic ash. Elevation ranges from 2,800 to 4,400 feet. These soils are in a climate with warm, dry summers and cool, moist winters. The average annual precipitation ranges from 17 to 40 inches. The average January temperature is about 28 degrees F, and average July temperature is about 64 degrees F. The average annual air temperature is 42 to 45 degrees F. Frost-free season is 60 to 110 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Weissenfels: Promising
- Alpowa: Weak indication
- Asotin: Weak indication
- Bolicker: Weak indication
- Bridgewater: Weak indication
- Chard: Weak indication
- Dallesport: Weak indication
- Ewall: Weak indication
See it on the map
Open a Cloverland spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Cloverland silt loam, 8 to 30 percent slopes, map unit 18 in Asotin County Area, Washington (Asotin and Garfield Counties).
- Official Series Description: Cloverland(revised 03/2013), established.
- Taxonomic class: Fine-silty, mixed, superactive, frigid Xeric Argialbolls
- Rated with rule version 2026-09-28.1; the method is on the About page.