Bridgewater soil
Wild-clay potential
Weak indication
Weak indication: no layer of Bridgewater shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Bridgewater soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Bridgewater spot on the map
Rated from the USDA soil survey record for Bridgewater extremely stony sandy loam, 0 to 15 percent slopes (Asotin County Area, Washington (Asotin and Garfield Counties)) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 3% clay.
- Lowers the potential Low engineering plasticity index (0): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 30 in (76 cm)).
- Note Typically starts about 30 in (76 cm) down; expect real digging or look for cuts and banks.
- Lowers the potential High rock content (about 57% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
Layer by layer
- Sandy layerH1 An extremely stony sandy loam layer about 0 to 8 in down: about 14% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
- Sandy layerH2 An extremely cobbly sandy loam layer about 8 to 30 in down: about 11% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
- Sandy layerH3best layer An extremely cobbly loamy sand layer about 30 to 60 in down: about 3% clay, low plasticity when wet, brown when moist. Weak indication
What it looks like raw
The sandy layer (H3), 30 to 60 in down in the typical profile: brown (10YR 5/3) dry, very dark grayish brown (10YR 3/2) moist; loose. Raw colour is not fired colour.
About the soil
- Parent material: alluvium.
- USDA family mineralogy: mixed.
- USDA family particle-size class: loamy-skeletal.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 3 map units in Idaho, Washington, in these survey areas: Asotin County Area, Washington (Asotin and Garfield Counties); Lewis and Nez Perce Counties, Idaho.
By state: wild clay in Idaho,wild clay in Washington.
USDA, distribution and extent: Southeastern Washington, western Idaho, and northeastern Oregon; MLRAs 8 and 9; small extent
USDA, geographic setting: Elevation--230 to 760 m
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Cloverland: Strong lead
- Cramont: Strong lead
- Taney: Strong lead
- Caldwell: Promising
- Latahco: Promising
- Naff: Promising
- Slickpoo: Promising
- Thatuna: Promising
See it on the map
Open a Bridgewater spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Bridgewater extremely stony sandy loam, 0 to 15 percent slopes, map unit 6 in Asotin County Area, Washington (Asotin and Garfield Counties).
- Official Series Description: Bridgewater(revised 09/2019), established.
- Taxonomic class: Loamy-skeletal, mixed, superactive, mesic Cumulic Haploxerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.