Bolicker soil
Wild-clay potential
Weak indication
Weak indication: no layer of Bolicker shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Bolicker soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Bolicker spot on the map
Rated from the USDA soil survey record for Bolicker silt loam, 15 to 30 percent slopes (Asotin County Area, Washington (Asotin and Garfield Counties)) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 14% clay.
- Lowers the potential Low engineering plasticity index (5): little plastic behavior expected when wet.
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 31 in (78 cm)).
- Note Typically starts about 29 in (74 cm) down; expect real digging or look for cuts and banks.
- Lowers the potential High rock content (about 41% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
- Note USDA reports about 10% calcium carbonate; lime in a clay body deserves testing.
Layer by layer
- Sandy layerH1 A silt loam layer about 0 to 11 in down: about 14% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
- Sandy layerH2 A silt loam layer about 11 to 29 in down: about 14% clay, low plasticity when wet, brown when moist. Weak indication
- Sandy layerH3best layer A very cobbly loam layer about 29 to 60 in down: about 14% clay, low plasticity when wet, very pale brown when moist. Weak indication
What it looks like raw
The sandy layer (H3), 29 to 60 in down in the typical profile: very pale brown (10YR 7/3), brown (10YR 5/3) moist; slightly hard, friable, slightly sticky and slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: loess over basalt colluvium.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 3 map units in Washington, in these survey areas: Asotin County Area, Washington (Asotin and Garfield Counties); Garfield County Area, Washington.
By state: wild clay in Washington.
USDA, distribution and extent: Southeastern Washington. MLRA 8. The series is of small extent.
USDA, geographic setting: Bolicker soils are on canyon walls, slumpblocks, and footslopes and back slopes of mountains. Slopes are 15 to 90 percent. These soils formed in loess over colluvium derived from basalt. Elevation is 800 to 2,600 feet. The mean annual precipitation is 12 to 15 inches. Summers are warm and dry and winters are cool and moist. The mean annual temperature is 48 to 51 degrees F. The frost-free season is 135 to 160 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Cloverland: Strong lead
- Weissenfels: Promising
- Chard: Weak indication
- Lickskillet: Weak indication
- Alpowa: Weak indication
- Asotin: Weak indication
- Bridgewater: Weak indication
- Dallesport: Weak indication
See it on the map
Open a Bolicker spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Bolicker silt loam, 15 to 30 percent slopes, map unit 4 in Asotin County Area, Washington (Asotin and Garfield Counties).
- Official Series Description: Bolicker(revised 11/2008), established.
- Taxonomic class: Coarse-loamy, mixed, superactive, mesic Calcic Haploxerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.