Linville soil
Wild-clay potential
Weak indication
Weak indication: no layer of Linville shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Linville soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Linville spot on the map
Rated from the USDA soil survey record for Linville silt loam, 40 to 70 percent slopes (Lewis and Nez Perce Counties, Idaho) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 24% clay. It may need settling or refining to become a clay body.
- Note USDA labels this a "Bt" horizon: a subsoil layer where clay has accumulated.
- Note Moderate engineering plasticity index (16).
- Raises the potential The official series description calls the wet soil moderately sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 48 in (122 cm)).
- Note Typically starts within about 19 in (48 cm) of the surface.
- Lowers the potential Noticeable rock fragments (about 26% by volume); screening would be needed and the clay percentage applies to the fine earth only.
Layer by layer
- TopsoilA A silt loam layer about 0 to 19 in down: about 20% clay, moderate plasticity when wet, very dark grayish brown when moist. Weak indication
- Clay subsoilBtbest layer A gravelly silt loam layer about 19 to 67 in down: about 24% clay, moderate plasticity when wet, brown when moist. Weak indication
What it looks like raw
The clay subsoil (Bt), 19 to 67 in down in the typical profile: brown (10YR 5/3) dry, dark grayish brown (10YR 4/2) moist; hard, friable, moderately sticky and moderately plastic. Raw colour is not fired colour.
About the soil
- Parent material: loess and colluvium derived from basalt.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 5 map units in Idaho, Washington, in these survey areas: Garfield County Area, Washington; Lewis and Nez Perce Counties, Idaho; Whitman County, Washington.
By state: wild clay in Idaho,wild clay in Washington.
USDA, distribution and extent: Eastern and central Washington, northeastern Oregon, Idaho; MLRAs 8 and 9; moderate extent
USDA, geographic setting: Elevation--240 to 1075 m
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Cramont: Strong lead
- Garfield: Strong lead
- Konert: Strong lead
- Latah: Strong lead
- Taney: Strong lead
- Tilma: Strong lead
- Caldwell: Promising
- Naff: Promising
See it on the map
Open a Linville spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 80%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Linville silt loam, 40 to 70 percent slopes, map unit 80 in Lewis and Nez Perce Counties, Idaho.
- Official Series Description: Linville(revised 09/2019), established.
- Taxonomic class: Fine-loamy, mixed, superactive, mesic Pachic Haploxerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.