Latah soil
Wild-clay potential
Strong lead
Strong lead: a clayey layer typically about 30 to 60 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Latah soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Latah silt loam (Whitman County, Washington) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 35% clay in the fine-earth portion.
- Raises the potential High engineering plasticity index (25): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil moderately sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 30 in (76 cm)).
- Note Typically starts about 30 in (76 cm) down; expect real digging or look for cuts and banks.
- Missing data Rock fragment content is not reported.
- Note High shrink-swell (linear extensibility about 7.5%): often very plastic, and prone to cracking as it dries.
- Note Engineering class CH: a clay of high plasticity in the Unified system.
Layer by layer
- Loamy layerH1 A silt loam layer about 0 to 19 in down: about 24% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
- Loamy layerH2 A silt loam layer about 19 to 30 in down: about 23% clay, low plasticity when wet, light gray when moist. Weak indication
- Clay-rich layerH3best layer A silty clay loam layer about 30 to 60 in down: about 35% clay, high plasticity when wet, brown when moist. Strong lead
What it looks like raw
The clay-rich layer (H3), 30 to 60 in down in the typical profile: brown (10YR 5/3) dry, brown (10YR 4/3) moist; hard, very firm, sticky and plastic. Raw colour is not fired colour.
About the soil
- Parent material: alluvium from loess and ash.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine.
- Drainage: somewhat poorly drained.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Idaho, Washington, in these survey areas: Latah County, Idaho; Whitman County, Washington.
By state: wild clay in Idaho,wild clay in Washington.
USDA, distribution and extent: Eastern Washington, northeastern Oregon, northern Idaho; MLRA 9; moderate extent
USDA, geographic setting: Elevation--550 to 975 m
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Garfield: Strong lead
- Tilma: Strong lead
- Driscoll: Strong lead
- Konert: Strong lead
- Naff: Promising
- Thatuna: Promising
- Caldwell: Promising
- Latahco: Promising
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Latah silt loam, map unit 54 in Whitman County, Washington.
- Official Series Description: Latah(revised 06/2016), established.
- Taxonomic class: Fine, mixed, superactive, mesic Xeric Argialbolls
- Rated with rule version 2026-09-28.1; the method is on the About page.