Stemilt soil
Wild-clay potential
Weak indication
Weak indication: no layer of Stemilt shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Stemilt soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Stemilt spot on the map
Rated from the USDA soil survey record for Stemilt silt loam, 25 to 45 percent slopes (Chelan County Area, Washington (Parts of Chelan and Kittitas Counties)) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clay-enriched layer: about 28% clay in the fine-earth portion.
- Note Moderate engineering plasticity index (10).
- Raises the potential The official series description calls the wet soil very sticky and very plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 43 in (109 cm)).
- Note Typically starts within about 17 in (43 cm) of the surface.
- Lowers the potential High rock content (about 49% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
Layer by layer
- Sandy layerH1 An ashy silt loam layer about 0 to 5 in down: about 8% clay, moderate plasticity when wet, dark grayish brown when moist. Weak indication
- Sandy layerH2 An ashy silt loam layer about 5 to 17 in down: about 8% clay, moderate plasticity when wet, brown when moist. Weak indication
- Loamy layerH3best layer An extremely cobbly silty clay loam layer about 17 to 60 in down: about 28% clay, moderate plasticity when wet, pale brown when moist. Weak indication
What it looks like raw
The loamy layer (H3), 17 to 60 in down in the typical profile: pale brown (10YR 6/3) dry, dark yellowish brown (10YR 4/4) moist; very hard, firm, very sticky and very plastic. Raw colour is not fired colour.
About the soil
- Parent material: residuum and colluvium from basalt or andesite with a component of volcanic ash.
- USDA family particle-size class: loamy-skeletal.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Washington, in these survey areas: Chelan County Area, Washington (Parts of Chelan and Kittitas Counties).
By state: wild clay in Washington.
USDA, distribution and extent: Central and north-central Washington; MLRA 6; moderate extent
USDA, geographic setting: Elevation--610 to 1650 m
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bjork: Promising
- Peoh: Promising
- Cowiche: Possible
- Morical: Possible
- Zen: Possible
- Anatone: Weak indication
- Ardenvoir: Weak indication
- Beverly: Weak indication
See it on the map
Open a Stemilt spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Stemilt silt loam, 25 to 45 percent slopes, map unit StE in Chelan County Area, Washington (Parts of Chelan and Kittitas Counties).
- Official Series Description: Stemilt(revised 09/2019), established.
- Taxonomic class: Loamy-skeletal, isotic, frigid Vitrandic Argixerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.