Sage soil
Wild-clay potential
Strong lead
Strong lead: a clayey layer typically about 5 to 40 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Sage soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Sage-Slickspots complex, 0 to 15 percent slopes (Butte County, South Dakota) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 48% clay in the fine-earth portion.
- Raises the potential High engineering plasticity index (35): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil moderately sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 35 in (89 cm)).
- Note Typically starts within about 5 in (13 cm) of the surface.
- Note Few rock fragments (about 2% by volume).
- Note High shrink-swell (linear extensibility about 17%): often very plastic, and prone to cracking as it dries.
- Note Engineering class CH: a clay of high plasticity in the Unified system.
Layer by layer
- Clay-rich layerH1 A silty clay loam layer about 0 to 5 in down: about 35% clay, high plasticity when wet, light brownish gray when moist. Promising
- Clay-rich layerH2best layer A silty clay layer about 5 to 40 in down: about 48% clay, high plasticity when wet, light brownish gray when moist. Strong lead
- Clay-rich layerH3 A silty clay layer about 40 to 60 in down: about 50% clay, high plasticity when wet, olive gray when moist. Strong lead
What it looks like raw
The clay-rich layer (H2), 5 to 40 in down in the typical profile: light brownish gray (2.5Y 6/2), dark grayish brown (2.5Y 4/2) moist; hard, firm, sticky and plastic. Raw colour is not fired colour.
About the soil
- Parent material: silty and clayey alluvium.
- USDA family particle-size class: fine.
- Drainage: poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 2 map units in South Dakota, in these survey areas: Butte County, South Dakota.
By state: wild clay in South Dakota.
USDA, distribution and extent: Northwestern South Dakota and southeastern Montana. It is of small extent.
USDA, geographic setting: Sage soils are on bottom lands and fans. Slope gradients range from 0 to 6 percent. The soils formed in clayey alluvium overlying clay shale, soft sandstone or stratified alluvium. The mean annual temperature ranges from 39 to 47 degrees F. The mean annual precipitation ranges from 14 to 16 inches. These soils have a seasonal high water table at the surface to a depth of about 2 feet.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Absher: Strong lead
- Arvada: Strong lead
- Belfield: Strong lead
- Bidman: Strong lead
- Hisle: Strong lead
- Kyle: Strong lead
- McKenzie: Strong lead
- Pierre: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 55%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Sage-Slickspots complex, 0 to 15 percent slopes, map unit Sa in Butte County, South Dakota.
- Official Series Description: Sage, established.
- Taxonomic class: Fine, smectitic, nonacid, mesic Typic Fluvaquents
- Rated with rule version 2026-09-28.1; the method is on the About page.