Belfield soil
Wild-clay potential
Strong lead
Strong lead: a clayey layer typically about 24 to 60 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Belfield soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Belfield spot on the map
Rated from the USDA soil survey record for Belfield-Loburn silt loams, 0 to 3 percent slopes (Butte County, South Dakota) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 36% clay in the fine-earth portion.
- Raises the potential High engineering plasticity index (20): USDA's estimate suggests plastic behavior when wet.
- Note Thick enough to investigate (about 36 in (91 cm)).
- Note Typically starts about 24 in (61 cm) down; expect real digging or look for cuts and banks.
- Missing data Rock fragment content is not reported.
- Note High shrink-swell (linear extensibility about 7.5%): often very plastic, and prone to cracking as it dries.
- Note USDA reports about 9% calcium carbonate; lime in a clay body deserves testing.
Layer by layer
- Loamy layerH1 A silt loam layer about 0 to 14 in down: about 23% clay, moderate plasticity when wet, grayish brown when moist. Possible
- Clay-rich layerH2 A silty clay loam layer about 14 to 24 in down: about 39% clay, high plasticity when wet, light olive brown when moist. Strong lead
- Clay-rich layerH3best layer A clay loam layer about 24 to 60 in down: about 36% clay, high plasticity when wet, light olive brown when moist. Strong lead
What it looks like raw
The clay-rich layer (H3), 24 to 60 in down in the typical profile: light olive brown (2.5Y 5/4), olive brown (2.5Y 4/4) moist; very hard, friable. Raw colour is not fired colour.
About the soil
- USDA family particle-size class: fine.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 2 map units in South Dakota, in these survey areas: Butte County, South Dakota.
By state: wild clay in South Dakota.
USDA, distribution and extent: Southwestern North Dakota, northwestern South Dakota, and eastern Montana. The soil is extensive.
USDA, geographic setting: Belfield soils are on level and nearly level terraces, flats and upland swales and on nearly level to moderately sloping uplands. Slopes from 1 to 4 percent are most common, but slope ranges from 0 to 9 percent. The soils formed in alkaline, calcareous residuum, or alluvium mainly of tertiary origin. Mean annual precipitation ranges from 13 to 18 inches, and mean annual air temperature ranges from 39 to 45 degrees F.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Absher: Strong lead
- Arvada: Strong lead
- Bidman: Strong lead
- Hisle: Strong lead
- Kyle: Strong lead
- McKenzie: Strong lead
- Pierre: Strong lead
- Sage: Strong lead
See it on the map
Open a Belfield spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 60%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Belfield-Loburn silt loams, 0 to 3 percent slopes, map unit BlA in Butte County, South Dakota.
- Official Series Description: Belfield(revised 01/2023), established.
- Taxonomic class: Fine, smectitic, frigid Glossic Natrustolls
- Rated with rule version 2026-09-28.1; the method is on the About page.