Redig soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 3 to 18 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Redig soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Redig clay loam, 9 to 25 percent slopes (Butte County, South Dakota) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 26% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (15).
- Note The official series description calls the wet soil slightly sticky.
- Note Thick enough to investigate (about 15 in (38 cm)).
- Note Typically starts within about 3 in (8 cm) of the surface.
- Note Few rock fragments (about 7% by volume).
- Note USDA reports about 10% calcium carbonate; lime in a clay body deserves testing.
Layer by layer
- Loamy layerH1 A clay loam layer about 0 to 3 in down: about 29% clay, moderate plasticity when wet, grayish brown when moist. Possible
- Loamy layerH2best layer A loam layer about 3 to 18 in down: about 26% clay, moderate plasticity when wet, white when moist. Possible
- Loamy layerH3 A gravelly loam layer about 18 to 45 in down: about 24% clay, moderate plasticity when wet, light brownish gray when moist. Weak indication
- Loamy layerH4 A gravelly clay loam layer about 45 to 60 in down: about 28% clay, moderate plasticity when wet, light brownish gray when moist. Possible
What it looks like raw
The loamy layer (H2), 3 to 18 in down in the typical profile: white (10YR 8/1), pale brown (10YR 6/3) moist; hard, friable, slightly sticky. Raw colour is not fired colour.
About the soil
- Parent material: loamy alluvium.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in South Dakota, in these survey areas: Butte County, South Dakota.
By state: wild clay in South Dakota.
USDA, distribution and extent: Western South Dakota. The series is of small extent.
USDA, geographic setting: Redig soils are on gently sloping to steep, convex surfaces where terrace deposits are remnants that cap ridges and upper slopes of undulating to rolling uplands. Slope gradients range from 6 to 25 percent. The soil formed in old alluvium containing sands, silts, clays, and rock fragments of mixed mineral origin. The mean annual air temperature ranges from 45 to 49 degrees F., and mean annual precipitation ranges from 10 to 15 inches.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Absher: Strong lead
- Arvada: Strong lead
- Belfield: Strong lead
- Bidman: Strong lead
- Hisle: Strong lead
- Kyle: Strong lead
- McKenzie: Strong lead
- Pierre: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Redig clay loam, 9 to 25 percent slopes, map unit RdE in Butte County, South Dakota.
- Official Series Description: Redig(revised 11/2002), established.
- Taxonomic class: Fine-loamy, mixed, superactive, mesic Gypsic Haplustepts
- Rated with rule version 2026-09-28.1; the method is on the About page.