Parshall soil
Wild-clay potential
Weak indication
Weak indication: no layer of Parshall shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Parshall soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Parshall spot on the map
Rated from the USDA soil survey record for Parshall fine sandy loam, 0 to 3 percent slopes (Butte County, South Dakota) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 13% clay.
- Lowers the potential Low engineering plasticity index (5): little plastic behavior expected when wet.
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 37 in (94 cm)).
- Note Typically starts within about 6 in (15 cm) of the surface.
- Missing data Rock fragment content is not reported.
Layer by layer
- Sandy layerH1 A fine sandy loam layer about 0 to 6 in down: about 13% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
- Sandy layerH2best layer A fine sandy loam layer about 6 to 43 in down: about 13% clay, low plasticity when wet, grayish brown when moist. Weak indication
- Sandy layerH3 A fine sandy loam layer about 43 to 60 in down: about 13% clay, low plasticity when wet, light yellowish brown when moist. Weak indication
What it looks like raw
The sandy layer (H2), 6 to 43 in down in the typical profile: grayish brown (2.5Y 5/2), dark grayish brown (2.5Y 4/2) moist; soft, very friable, slightly sticky and slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: coarse-loamy slope alluvium derived from sandstone.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in South Dakota, in these survey areas: Butte County, South Dakota.
By state: wild clay in South Dakota.
USDA, distribution and extent: Western North Dakota, northwestern South Dakota and eastern Montana. The soil is extensive.
USDA, geographic setting: Parshall soils are on level to moderately steep high terraces along river valleys, on outwash plains, and in swales on uplands. Slope gradients are commonly less than 4 percent but range from 0 to 25 percent. The soils formed in alluvium. Mean annual air temperature is 35 to 45 degrees F, and mean annual precipitation is 12 to 18 inches.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Absher: Strong lead
- Arvada: Strong lead
- Belfield: Strong lead
- Bidman: Strong lead
- Hisle: Strong lead
- Kyle: Strong lead
- McKenzie: Strong lead
- Pierre: Strong lead
See it on the map
Open a Parshall spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Parshall fine sandy loam, 0 to 3 percent slopes, map unit PaA in Butte County, South Dakota.
- Official Series Description: Parshall, established.
- Taxonomic class: Coarse-loamy, mixed, superactive, frigid Pachic Haplustolls
- Rated with rule version 2026-09-28.1; the method is on the About page.