Logy soil
Wild-clay potential
Weak indication
Weak indication: no layer of Logy shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Logy soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Logy cobbly sandy loam, 3 to 15 percent slopes (Douglas County, Washington) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 4% clay.
- Lowers the potential Low engineering plasticity index (2.5): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 32 in (81 cm)).
- Note Typically starts about 28 in (71 cm) down; expect real digging or look for cuts and banks.
- Lowers the potential High rock content (about 51% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
Layer by layer
- Sandy layerH1 A cobbly sandy loam layer about 0 to 10 in down: about 8% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
- Sandy layerH2 A very gravelly sandy loam layer about 10 to 28 in down: about 9% clay, low plasticity when wet, dark brown when moist. Weak indication
- Sandy layerH3best layer A stratified extremely gravelly coarse sand to gravelly sandy loam layer about 28 to 60 in down: about 4% clay, low plasticity when wet, brown when moist. Weak indication
What it looks like raw
The sandy layer (H3), 28 to 60 in down in the typical profile: brown (10YR 5/3), dark brown (10YR 3/3) moist; loose. Raw colour is not fired colour.
About the soil
- Parent material: alluvium and colluvium.
- USDA family mineralogy: mixed.
- USDA family particle-size class: loamy-skeletal.
- Drainage: somewhat excessively drained.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Washington, in these survey areas: Douglas County, Washington.
By state: wild clay in Washington.
USDA, distribution and extent: Central Washington. Series is of small extent.
USDA, geographic setting: Logy soils are on flood plains and alluvial fans at elevations of 700 to 2,400 feet. These soils formed in alluvium. Slopes are 0 to 30 percent. They are in a climate with a mean annual precipitation of 7 to 12 inches, warm dry summers and cold moist winters. Average January temperature is 29 degrees F.; average July temperature is 73 degrees F.; and average annual temperature is 51 degrees F. Frost-free season is 130 to 180 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Cashmere: Weak indication
- Cashmont: Weak indication
- Entiat: Weak indication
- Kiona: Weak indication
- Peshastin: Weak indication
- Pogue: Weak indication
- Quincy: Weak indication
- Bellingham: Strong lead(same state)
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Logy cobbly sandy loam, 3 to 15 percent slopes, map unit 222 in Douglas County, Washington.
- Official Series Description: Logy, established.
- Taxonomic class: Loamy-skeletal, mixed, superactive, mesic Torrifluventic Haploxerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.