Letort soil
Wild-clay potential
Weak indication
Weak indication: no layer of Letort shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Letort soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Letort silt loam, 0 to 3 percent slopes (Lancaster County, Pennsylvania) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 27% clay. It may need settling or refining to become a clay body.
- Note USDA labels this a "Bt" horizon: a subsoil layer where clay has accumulated.
- Note Moderate engineering plasticity index (7.5).
- Lowers the potential The official series description calls the wet soil nonsticky and nonplastic.
- Note Thick enough to investigate (about 23 in (58 cm)).
- Note Typically starts within about 9 in (23 cm) of the surface.
- Note Few rock fragments (about 12% by volume).
Layer by layer
- TopsoilAp A silt loam layer about 0 to 9 in down: about 20% clay, low plasticity when wet, dark brown when moist. Weak indication
- Clay subsoilBtbest layer A silt loam layer about 9 to 32 in down: about 27% clay, moderate plasticity when wet, dark grayish brown when moist. Weak indication
- Loamy layerC1 A silt loam layer about 32 to 46 in down: about 22% clay, low plasticity when wet, very dark grayish brown when moist. Weak indication
- Loamy layerC2 A channery loam layer about 46 to 62 in down: about 20% clay, low plasticity when wet, very dark grayish brown when moist. Weak indication
What it looks like raw
The clay subsoil (Bt), 9 to 32 in down in the typical profile: dark grayish brown (2.5Y 4/2); friable, nonsticky, nonplastic. Raw colour is not fired colour.
About the soil
- Parent material: residuum weathered from limestone.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
- Lithic bedrock typically about 80 in (202 cm) down.
Where it is mapped
Seen on the map as the most common soil in 3 map units in Pennsylvania, in these survey areas: Lancaster County, Pennsylvania.
By state: wild clay in Pennsylvania.
USDA, distribution and extent: Southeastern Pennsylvania. The series is of moderate extent.
USDA, geographic setting: Letort soils are nearly level to moderately steep soils on uplands. Slopes range from 0 to 25 percent. The soils formed in residuum weathered from interbedded micaceous limestone, graphitic phyllite, and schist. Climate is humid and temperate, with mean annual precipitation of 40 to 46 inches; mean annual temperature ranges from 52 to 55 degrees F., and the growing season ranges from 170 to 190 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Hagerstown: Strong lead
- Watchung: Strong lead
- Baile: Promising
- Bowmansville: Promising
- Bucks: Promising
- Chester: Promising
- Conestoga: Promising
- Duffield: Promising
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 90%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Letort silt loam, 0 to 3 percent slopes, map unit LdA in Lancaster County, Pennsylvania.
- Official Series Description: Letort(revised 06/2001), established.
- Taxonomic class: Fine-loamy, mixed, superactive, mesic Typic Hapludalfs
- Rated with rule version 2026-09-28.1; the method is on the About page.