Chester soil
Wild-clay potential
Promising
Promising: a clay-enriched layer typically about 30 to 38 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Chester soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Chester spot on the map
Rated from the USDA soil survey record for Chester silt loam, 0 to 3 percent slopes (Harford County Area, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clay-enriched layer: about 34% clay in the fine-earth portion.
- Note USDA labels this a "Bt3" horizon: a subsoil layer where clay has accumulated.
- Raises the potential High engineering plasticity index (24): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil moderately sticky and moderately plastic (a field observation, not a ceramic test).
- Note Moderate thickness (about 8 in (21 cm)).
- Note Typically starts about 30 in (76 cm) down; expect real digging or look for cuts and banks.
- Note Few rock fragments (about 7% by volume).
Layer by layer
- TopsoilAp A silt loam layer about 0 to 10 in down: about 22% clay, moderate plasticity when wet, dark grayish brown when moist. Weak indication
- Loamy layerBE A silt loam layer about 10 to 17 in down: about 23% clay, moderate plasticity when wet, brown when moist. Possible
- Clay subsoilBt1 A clay loam layer about 17 to 22 in down: about 31% clay, high plasticity when wet, brown when moist. Possible
- Clay subsoilBt2 A clay loam layer about 22 to 30 in down: about 33% clay, high plasticity when wet, brown when moist. Promising
- Clay subsoilBt3best layer A clay loam layer about 30 to 38 in down: about 34% clay, high plasticity when wet, yellowish red when moist. Promising
- Clay subsoilBt4 A loam layer about 38 to 56 in down: about 26% clay, moderate plasticity when wet, brown when moist. Possible
- Sandy layerC A fine sandy loam layer about 56 to 92 in down: about 10% clay, low plasticity when wet, variegated yellowish red when moist. Weak indication
What it looks like raw
The clay subsoil (Bt3), 30 to 38 in down in the typical profile: yellowish red (5YR 4/6); silty clay loam; firm, sticky, plastic. Raw colour is not fired colour.
About the soil
- Parent material: residuum weathered from mica schist.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 23 map units in Maryland, Pennsylvania, in these survey areas: Chester County, Pennsylvania; Delaware County, Pennsylvania; Harford County Area, Maryland; Lancaster County, Pennsylvania; Lebanon County, Pennsylvania; Montgomery County, Pennsylvania; Philadelphia County, Pennsylvania; York County, Pennsylvania.
By state: wild clay in Maryland,wild clay in Pennsylvania.
USDA, distribution and extent: Maryland, Delaware, Pennsylvania, and Virginia. The series is of large extent.
USDA, geographic setting: Chester soils are on upland divides and upper slopes in the northern Piedmont Plateau. Slopes are most commonly 3 to 10 percent but range from 0 to 65 percent. The soils formed in residuum from micaceous schist. The climate is temperate and humid with mean annual temperature of 50 to 57 degrees F. and mean annual precipitation of 35 to 45 inches. Frost-free days range from 150 to 200.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Watchung: Strong lead
- Hagerstown: Strong lead
- Montalto: Strong lead
- Kelly: Strong lead
- Kinkora: Strong lead
- Talleyville: Strong lead
- Glenelg: Promising
- Hatboro: Promising
See it on the map
Open a Chester spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 80%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Chester silt loam, 0 to 3 percent slopes, map unit CcA in Harford County Area, Maryland.
- Official Series Description: Chester(revised 02/2008), established.
- Taxonomic class: Fine-loamy, mixed, semiactive, mesic Typic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.