Clymer soil
Wild-clay potential
Weak indication
Weak indication: no layer of Clymer shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Clymer soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Clymer very stony loam, 3 to 8 percent slopes (Lancaster County, Pennsylvania) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 13% clay.
- Lowers the potential Low engineering plasticity index (4.5): little plastic behavior expected when wet.
- Lowers the potential The official series description calls the wet soil nonsticky and nonplastic.
- Note Thick enough to investigate (about 33 in (84 cm)).
- Note Typically starts about 27 in (68 cm) down; expect real digging or look for cuts and banks.
- Lowers the potential High rock content (about 48% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
Layer by layer
- TopsoilA A channery loam layer about 0 to 7 in down: about 21% clay, low plasticity when wet, very dark grayish brown when moist. Weak indication
- Clay subsoilBt A channery sandy loam layer about 7 to 27 in down: about 16% clay, low plasticity when wet, yellowish brown when moist. Weak indication
- Sandy layerCbest layer A very channery sandy loam layer about 27 to 60 in down: about 13% clay, low plasticity when wet, yellowish brown when moist. Weak indication
What it looks like raw
The sandy layer (C), 27 to 60 in down in the typical profile: yellowish brown (10YR 5/6); extremely channery coarse sandy loam; friable, nonsticky, nonplastic. Raw colour is not fired colour.
About the soil
- Parent material: residuum weathered from sandstone.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
- Lithic bedrock typically about 58 in (147 cm) down.
Where it is mapped
Seen on the map as the most common soil in 3 map units in Pennsylvania, in these survey areas: Lancaster County, Pennsylvania.
By state: wild clay in Pennsylvania.
USDA, distribution and extent: Distribution: Pennsylvania, Kentucky, Maryland, Ohio, Virginia, and West Virginia
USDA, geographic setting: Landscape: Hills
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Hagerstown: Strong lead
- Watchung: Strong lead
- Baile: Promising
- Bowmansville: Promising
- Bucks: Promising
- Chester: Promising
- Conestoga: Promising
- Duffield: Promising
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 90%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Clymer very stony loam, 3 to 8 percent slopes, map unit ClB in Lancaster County, Pennsylvania.
- Official Series Description: Clymer(revised 09/2015), established.
- Taxonomic class: Coarse-loamy, siliceous, active, mesic Typic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.