Burch soil
Wild-clay potential
Weak indication
Weak indication: no layer of Burch shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Burch soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Burch fine sandy loam, 0 to 3 percent slopes (Chelan County Area, Washington (Parts of Chelan and Kittitas Counties)) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 13% clay.
- Lowers the potential Low engineering plasticity index (5): little plastic behavior expected when wet.
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 52 in (132 cm)).
- Note Typically starts within about 8 in (20 cm) of the surface.
- Note Few rock fragments (about 5% by volume).
Layer by layer
- Sandy layerH1 A fine sandy loam layer about 0 to 8 in down: about 9% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
- Sandy layerH2best layer A loam layer about 8 to 60 in down: about 13% clay, low plasticity when wet, yellowish brown when moist. Weak indication
What it looks like raw
The sandy layer (H2), 8 to 60 in down in the typical profile: yellowish brown (10YR 5/4), dark brown (10YR 4/3) moist; slightly hard, friable, slightly sticky and slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: alluvium derived from sandstone.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 4 map units in Washington, in these survey areas: Chelan County Area, Washington (Parts of Chelan and Kittitas Counties).
By state: wild clay in Washington.
USDA, distribution and extent: North-central Washington. Burch soils are moderately extensive.
USDA, geographic setting: Burch soils are on terraces at elevations of 700 to 1,200 feet in Washington, and 3,500 to 4,600 feet in Idaho. Slopes are 0 to 45 percent. They formed in alluvium, primarily of sandstone origin. These soils occur in a climate with hot dry summers and moist cold summers. Average annual precipitation is 8 to 12 inches. Average January temperature is 26 degrees F. to 28 degrees F., average July temperature is 72 degrees F. to 74 degrees F. and average annual temperature is 48 to 51 degrees F., and average frost-free season is 145 to 190 days in Washington, and 100 to 120 days in Idaho.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bjork: Promising
- Peoh: Promising
- Cowiche: Possible
- Morical: Possible
- Zen: Possible
- Anatone: Weak indication
- Ardenvoir: Weak indication
- Beverly: Weak indication
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Burch fine sandy loam, 0 to 3 percent slopes, map unit BuA in Chelan County Area, Washington (Parts of Chelan and Kittitas Counties).
- Official Series Description: Burch, established.
- Taxonomic class: Coarse-loamy, mixed, superactive, mesic Aridic Haploxerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.