Bethesda soil
Wild-clay potential
Weak indication
Weak indication: no layer of Bethesda shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Bethesda soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Bethesda spot on the map
Rated from the USDA soil survey record for Bethesda-Fairpoint channery silt loams, 0 to 8 percent slopes (Warren and Forest Counties, Pennsylvania) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clay-enriched layer: about 30% clay in the fine-earth portion.
- Raises the potential High engineering plasticity index (20): USDA's estimate suggests plastic behavior when wet.
- Note Thick enough to investigate (about 76 in (193 cm)).
- Note Typically starts within about 3 in (7 cm) of the surface.
- Lowers the potential High rock content (about 72% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
Layer by layer
- Loamy layer^A A channery silt loam layer about 0 to 3 in down: about 21% clay, moderate plasticity when wet, dark grayish brown when moist. Weak indication
- Loamy layer^Cbest layer An extremely channery silty clay loam layer about 3 to 79 in down: about 30% clay, high plasticity when wet, percent brown when moist. Weak indication
What it looks like raw
The loamy layer (^C), 3 to 79 in down in the typical profile: percent brown (10YR 4/3), percent yellowish brown (10YR 5/4); very firm. Raw colour is not fired colour.
About the soil
- Dug, graded, or filled ground, not a natural soil. USDA's layers for Bethesda are an estimate for moved material and can change within a few steps, so it is rated no higher than Possible.
- Parent material: acid coal extraction mine spoil derived from sandstone and shale.
- USDA family mineralogy: mixed.
- USDA family particle-size class: loamy-skeletal.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Pennsylvania, in these survey areas: Warren and Forest Counties, Pennsylvania.
By state: wild clay in Pennsylvania.
USDA, distribution and extent: Distribution: Ohio, Illinois, Indiana, Kentucky, Missouri, Pennsylvania, Tennessee, Virginia and West Virginia
USDA, geographic setting: MLRAs: 113 (Central Claypan Areas), 114 (Southern Illinois and Indiana Thin Loess and Till Plain), 115 (Central Mississippi Valley Wooded Slopes), 124 (Western Allegheny Plateau), 125 (Cumberland Plateau and Mountains) and 126 (Central Allegheny Plateau)
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Armagh: Strong lead
- Cavode: Strong lead
- Brinkerton: Promising
- Ernest: Promising
- Shelmadine: Promising
- Wharton: Promising
- Alvira: Possible
- Atkins: Possible
See it on the map
Open a Bethesda spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 48%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Bethesda-Fairpoint channery silt loams, 0 to 8 percent slopes, map unit BfB in Warren and Forest Counties, Pennsylvania.
- Official Series Description: Bethesda(revised 12/2012), established.
- Taxonomic class: Loamy-skeletal, mixed, active, acid, mesic Typic Udorthents
- Rated with rule version 2026-09-28.1; the method is on the About page.