Badge soil
Wild-clay potential
Weak indication
Weak indication: no layer of Badge shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Badge soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Badge-Immiant-Rubble land complex, 20 to 70 percent slopes (Elmore County Area, Idaho, Parts of Elmore and Owyhee Counties) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clay-enriched layer: about 34% clay in the fine-earth portion.
- Note USDA labels this a "Bt1" horizon: a subsoil layer where clay has accumulated.
- Raises the potential High engineering plasticity index (24): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil moderately sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 22 in (56 cm)).
- Note Typically starts within about 21 in (53 cm) of the surface.
- Lowers the potential High rock content (about 39% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
Layer by layer
- TopsoilA A gravelly loam layer about 0 to 3 in down: about 20% clay, moderate plasticity when wet, dark grayish brown when moist. Weak indication
- TopsoilAB A gravelly loam layer about 3 to 21 in down: about 20% clay, moderate plasticity when wet, yellowish brown when moist. Weak indication
- Clay subsoilBt1best layer A very gravelly clay loam layer about 21 to 43 in down: about 34% clay, high plasticity when wet, yellowish brown when moist. Weak indication
- Clay subsoilBt2 A very stony clay loam layer about 43 to 54 in down: about 34% clay, high plasticity when wet, yellowish brown when moist. Weak indication
- BedrockR Bedrock about 54 to 64 in down: no clay layer to dig. Weak indication
What it looks like raw
The clay subsoil (Bt1), 21 to 43 in down in the typical profile: yellowish brown (10YR 5/4) dry, brown (10YR 4/3) moist; hard, firm, moderately sticky and moderately plastic. Raw colour is not fired colour.
About the soil
- Parent material: alluvium over bedrock derived from volcanic rock.
- USDA family mineralogy: mixed.
- USDA family particle-size class: loamy-skeletal.
- Drainage: well drained.
- Lithic bedrock typically about 54 in (137 cm) down.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Idaho, in these survey areas: Elmore County Area, Idaho, Parts of Elmore and Owyhee Counties.
By state: wild clay in Idaho.
USDA, distribution and extent: Eastern Washington and southern Idaho; MLRAs 8 and 10; moderate extent
USDA, geographic setting: Elevation--460 to 1225 m in Washington, 1225 to 1675 m in Idaho
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Chilcott: Strong lead
- Kunaton: Strong lead
- Farrot: Promising
- Haw: Promising
- Simonton: Promising
- Brownlee: Possible
- Colthorp: Possible
- Elkcreek: Possible
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 35%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Badge-Immiant-Rubble land complex, 20 to 70 percent slopes, map unit 6 in Elmore County Area, Idaho, Parts of Elmore and Owyhee Counties.
- Official Series Description: Badge(revised 09/2019), established.
- Taxonomic class: Loamy-skeletal, mixed, superactive, mesic Typic Argixerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.