Chilcott soil
Wild-clay potential
Strong lead
Strong lead: a clay-enriched layer typically about 9 to 15 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Chilcott soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Chilcott spot on the map
Rated from the USDA soil survey record for Chilcott silt loam, bedrock substratum, 0 to 2 percent slopes (Ada County, Idaho) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 48% clay in the fine-earth portion.
- Note USDA labels this a "Bt" horizon: a subsoil layer where clay has accumulated.
- Raises the potential High engineering plasticity index (35): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil very sticky and very plastic (a field observation, not a ceramic test).
- Note Moderate thickness (about 6 in (15 cm)).
- Note Typically starts within about 9 in (23 cm) of the surface.
- Note Few rock fragments (about 2% by volume).
- Note High shrink-swell (linear extensibility about 7.5%): often very plastic, and prone to cracking as it dries.
- Note USDA reports about 8% calcium carbonate; lime in a clay body deserves testing.
- Note Engineering class CH: a clay of high plasticity in the Unified system.
Layer by layer
- Sandy layerE A silt loam layer about 0 to 9 in down: about 15% clay, moderate plasticity when wet, light brownish gray when moist. Weak indication
- Clay subsoilBtbest layer A silty clay layer about 9 to 15 in down: about 48% clay, high plasticity when wet, brown when moist. Strong lead
- Loamy layerBk A loam layer about 15 to 26 in down: about 25% clay, moderate plasticity when wet. Possible
- Bkqm A cemented material layer about 26 to 47 in down: USDA gives no clay percentage or texture for it. Not enough data
- BedrockR Bedrock about 47 to 57 in down: no clay layer to dig. Weak indication
What it looks like raw
The clay subsoil (Bt), 9 to 15 in down in the typical profile: brown (10YR 5/3), brown (10YR 4/3) moist; very hard, firm, very sticky and very plastic. Raw colour is not fired colour.
About the soil
- Parent material: volcanic ash and/or mixed alluvium and/or loess over bedrock derived from basalt.
- USDA family mineralogy: smectitic. Smectite-rich clays are usually very plastic and shrink a lot as they dry.
- USDA family particle-size class: fine.
- Drainage: well drained.
- Lithic bedrock typically about 47 in (119 cm) down.
Where it is mapped
Seen on the map as the most common soil in 17 map units in Idaho, in these survey areas: Ada County, Idaho; Elmore County Area, Idaho, Parts of Elmore and Owyhee Counties; Owyhee County Area, Idaho.
By state: wild clay in Idaho.
USDA, distribution and extent: Southwestern Idaho and eastern Oregon. MLRA 10, 11, and 25. Chilcott soils are extensive.
USDA, geographic setting: Chilcott soils are nearly level to moderately steep on high terraces, mesas, calderas, shield volcanos and basalt plains at elevations of 2,300 to 5,300 feet. Slopes range from 0 to 30 percent. These soils formed in a thin mantle of loess over silty alluvium from loess and weathered volcanic ash over loamy or sandy and gravelly alluvium from igneous materials. The climate is cool, moist in the winter and hot, dry in the summer. Average annual precipitation is dominantly 8 to 12 inches, but ranges to 15 inches in the Boise Front (Ada County, Idaho). Average annual temperature is 45 to 54 degrees F. Frost-free period is 90 to 170 days. terms used throughout MLRA 11 to identify the setting of...
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Kunaton: Strong lead
- Aldape: Strong lead
- Aradaran: Strong lead
- Bowns: Strong lead
- Breadloaf: Strong lead
- Brent: Strong lead
- Castlerock: Strong lead
- Catchell: Strong lead
See it on the map
Open a Chilcott spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 90%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Chilcott silt loam, bedrock substratum, 0 to 2 percent slopes, map unit 30 in Ada County, Idaho.
- Official Series Description: Chilcott(revised 02/2002), established.
- Taxonomic class: Fine, smectitic, mesic Abruptic Xeric Argidurids
- Rated with rule version 2026-09-28.1; the method is on the About page.