Catchell soil
Wild-clay potential
Strong lead
Strong lead: a clay-enriched layer typically about 6 to 19 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Catchell soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Catchell spot on the map
Rated from the USDA soil survey record for Catchell-Chilcott-Banbury complex, 1 to 12 percent slopes (Ada County, Idaho) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 50% clay in the fine-earth portion.
- Note USDA labels this a "2Bt" horizon: a subsoil layer where clay has accumulated.
- Raises the potential High engineering plasticity index (37): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil very sticky and very plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 13 in (33 cm)).
- Note Typically starts within about 6 in (15 cm) of the surface.
- Note Few rock fragments (about 0% by volume).
- Note High shrink-swell (linear extensibility about 11%): often very plastic, and prone to cracking as it dries.
- Note Engineering class CH: a clay of high plasticity in the Unified system.
Layer by layer
- Sandy layerE1 A silt loam layer about 0 to 2 in down: about 12% clay, moderate plasticity when wet, light brownish gray when moist. Weak indication
- Sandy layerE2 A silt loam layer about 2 to 6 in down: about 12% clay, moderate plasticity when wet, light brownish gray when moist. Weak indication
- Clay subsoil2Btbest layer A silty clay layer about 6 to 19 in down: about 50% clay, high plasticity when wet, brown when moist. Strong lead
- Clay subsoil2Btk A silty clay layer about 19 to 22 in down: about 45% clay, high plasticity when wet, pale brown when moist. Promising
- Loamy layer2Bkq A clay loam layer about 22 to 25 in down: about 28% clay, moderate plasticity when wet, pale brown when moist. Possible
- 2Bkqm A cemented material layer about 25 to 30 in down: USDA gives no clay percentage or texture for it. Not enough data
- Bedrock3R Bedrock about 30 to 34 in down: no clay layer to dig. Weak indication
What it looks like raw
The clay subsoil (2Bt), 6 to 19 in down in the typical profile: brown (10YR 5/3), dark yellowish brown (10YR 3/4) moist; hard, firm, very sticky and very plastic. Raw colour is not fired colour.
About the soil
- Parent material: loess over silty alluvium and/or colluvium derived from basalt over basalt.
- USDA family mineralogy: smectitic. Smectite-rich clays are usually very plastic and shrink a lot as they dry.
- USDA family particle-size class: fine.
- Drainage: well drained.
- Lithic bedrock typically about 30 in (76 cm) down.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Idaho, in these survey areas: Ada County, Idaho.
By state: wild clay in Idaho.
USDA, distribution and extent: Southwestern and southcentral Idaho; MLRA 11 and 25. The series is inextensive.
USDA, geographic setting: These soils are on plug domes (buttes), lava flow lobes, pressure ridges and tumuli on shield volcanoes and lava plains, and on structural benches, mesas, buttes, and foothills with slopes of 0 to 30 percent. Elevation ranges from 850 to 1625 meters. The soils formed in a thin mantle of loess over silty alluvium from loess and weathered volcanic ash mixed with colluvium from basalt or welded rhyolitic tuff. The climate is semiarid and summers are dry. The average annual temperature is about 7 to 12 degrees C, and the average annual precipitation is about 200 to 330 mm, including up to 910 mm of snow. The frost-free period is about 90 to 150 days. - terms used throughout MLRA 11 to identify...
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Aldape: Strong lead
- Aradaran: Strong lead
- Bowns: Strong lead
- Breadloaf: Strong lead
- Brent: Strong lead
- Castlerock: Strong lead
- Chardoton: Strong lead
- Chilcott: Strong lead
See it on the map
Open a Catchell spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 35%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Catchell-Chilcott-Banbury complex, 1 to 12 percent slopes, map unit 4104 in Ada County, Idaho.
- Official Series Description: Catchell(revised 08/2021), established.
- Taxonomic class: Fine, smectitic, mesic Abruptic Xeric Argidurids
- Rated with rule version 2026-09-28.1; the method is on the About page.