Aldape soil
Wild-clay potential
Strong lead
Strong lead: a clay-enriched layer typically about 14 to 22 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Aldape soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Aldape loam, 4 to 15 percent slopes (Ada County, Idaho) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 40% clay in the fine-earth portion.
- Note USDA labels this a "Bt1" horizon: a subsoil layer where clay has accumulated.
- Raises the potential High engineering plasticity index (29): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil very sticky and very plastic (a field observation, not a ceramic test).
- Note Moderate thickness (about 8 in (20 cm)).
- Note Typically starts within about 14 in (36 cm) of the surface.
- Note Few rock fragments (about 0% by volume).
- Note High shrink-swell (linear extensibility about 8.8%): often very plastic, and prone to cracking as it dries.
- Note Engineering class CH: a clay of high plasticity in the Unified system.
Layer by layer
- TopsoilA1 A loam layer about 0 to 5 in down: about 16% clay, moderate plasticity when wet, grayish brown when moist. Weak indication
- TopsoilA2 A loam layer about 5 to 11 in down: about 18% clay, moderate plasticity when wet, brown when moist. Possible
- Clay subsoilBt/E A clay loam layer about 11 to 14 in down: about 28% clay, high plasticity when wet, pale brown when moist. Possible
- Clay subsoilBt1best layer A clay layer about 14 to 22 in down: about 40% clay, high plasticity when wet, pale brown when moist. Strong lead
- Clay subsoilBt2 A clay loam layer about 22 to 29 in down: about 30% clay, high plasticity when wet, pale brown when moist. Promising
- Clay subsoilBtk A loam layer about 29 to 35 in down: about 24% clay, moderate plasticity when wet, light yellowish brown when moist. Possible
- Loamy layerBk A sandy loam layer about 35 to 47 in down: about 18% clay, moderate plasticity when wet, light yellowish brown when moist. Weak indication
- Sandy layerBkq A sandy loam layer about 47 to 53 in down: about 16% clay, moderate plasticity when wet, very pale brown when moist. Weak indication
- 2Bkqm A cemented material layer about 53 to 60 in down: USDA gives no clay percentage or texture for it. Not enough data
What it looks like raw
The clay subsoil (Bt1), 14 to 22 in down in the typical profile: pale brown (10YR 6/3), brown (10YR 4/3) moist; very hard, very firm, very sticky and very plastic. Raw colour is not fired colour.
About the soil
- Parent material: loess and/or weathered volcanic ash over sandy alluvium.
- USDA family mineralogy: smectitic. Smectite-rich clays are usually very plastic and shrink a lot as they dry.
- USDA family particle-size class: fine.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 4 map units in Idaho, in these survey areas: Ada County, Idaho.
By state: wild clay in Idaho.
USDA, distribution and extent: Southwestern Idaho. MLRA 11. Aldape soils are not extensive.
USDA, geographic setting: Aldape soils are on southerly facing hill backslopes and footslopes, structural benches, fan remnants and landslides at elevations of 2,600 to 3,750 feet. Slopes range from 3 to 35 percent. These soils formed in alluvium from lacustrine deposits and volcanic ash. Average annual precipitation is 11 to 16 inches. Average annual temperature is 49 to 52 degrees F. Frost-free period is 125 to 155 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Aradaran: Strong lead
- Bowns: Strong lead
- Breadloaf: Strong lead
- Brent: Strong lead
- Castlerock: Strong lead
- Catchell: Strong lead
- Chardoton: Strong lead
- Chilcott: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Aldape loam, 4 to 15 percent slopes, map unit 2247 in Ada County, Idaho.
- Official Series Description: Aldape(revised 07/2011), established.
- Taxonomic class: Fine, smectitic, mesic Aridic Palexerolls
- Rated with rule version 2026-09-28.1; the method is on the About page.