Colthorp soil
Wild-clay potential
Possible
Possible: a clay-enriched layer typically about 4 to 8 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Colthorp soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Colthorp spot on the map
Rated from the USDA soil survey record for Colthorp silt loam, 0 to 2 percent slopes (Ada County, Idaho) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clay-enriched layer: about 28% clay in the fine-earth portion.
- Note USDA labels this a "Bt" horizon: a subsoil layer where clay has accumulated.
- Raises the potential High engineering plasticity index (20): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil moderately sticky and moderately plastic (a field observation, not a ceramic test).
- Lowers the potential Thin layer (about 4 in (10 cm)), hard to collect in quantity.
- Note Typically starts within about 4 in (10 cm) of the surface.
- Note Few rock fragments (about 0% by volume).
Layer by layer
- TopsoilA A silt loam layer about 0 to 4 in down: about 15% clay, moderate plasticity when wet, pale brown when moist. Weak indication
- Clay subsoilBtbest layer A silty clay loam layer about 4 to 8 in down: about 28% clay, high plasticity when wet, brown when moist. Possible
- Loamy layerBC A silt loam layer about 8 to 13 in down: about 21% clay, moderate plasticity when wet, light yellowish brown when moist. Weak indication
- Sandy layerBkq A loam layer about 13 to 19 in down: about 14% clay, moderate plasticity when wet, very pale brown when moist. Weak indication
- Bkqm A cemented material layer about 19 to 28 in down: USDA gives no clay percentage or texture for it. Not enough data
- Bedrock2R Bedrock about 28 to 38 in down: no clay layer to dig. Weak indication
What it looks like raw
The clay subsoil (Bt), 4 to 8 in down in the typical profile: brown (10YR 5/3), dark yellowish brown (10YR 4/4) moist; hard, friable, moderately sticky and moderately plastic. Raw colour is not fired colour.
About the soil
- Parent material: mixed alluvium and/or loess over bedrock derived from basalt.
- USDA family mineralogy: mixed.
- USDA family particle-size class: loamy.
- Drainage: well drained.
- Lithic bedrock typically about 28 in (71 cm) down.
Where it is mapped
Seen on the map as the most common soil in 7 map units in Idaho, in these survey areas: Ada County, Idaho; Elmore County Area, Idaho, Parts of Elmore and Owyhee Counties.
By state: wild clay in Idaho.
USDA, distribution and extent: Southwestern and south central Idaho; MLRA 11. It is of moderate extent.
USDA, geographic setting: Colthorp soils are on basalt plains, terraces and on plug domes and lava flow lobes on lava plains and shield volcanoes. Elevations range from 2,600 to 4,700 feet. Slopes are 0 to 20 percent. The soils formed in silty alluvium from loess and weathered volcanic ash overlying basalt. Winters are cool and moist and summers are hot and dry. Average annual precipitation is 8 to 12 inches. Average January temperature is about 28 degrees F.; average July temperature is about 73 degrees F.; average annual temperature is 48 to 53 degrees F. The frost free season is about 100 to 160 days. - terms used throughout MLRA 11 to identify the setting of this soil are quire varied although all equate to the...
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Chilcott: Strong lead
- Kunaton: Strong lead
- Aldape: Strong lead
- Aradaran: Strong lead
- Bowns: Strong lead
- Breadloaf: Strong lead
- Brent: Strong lead
- Castlerock: Strong lead
See it on the map
Open a Colthorp spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 90%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Colthorp silt loam, 0 to 2 percent slopes, map unit 40 in Ada County, Idaho.
- Official Series Description: Colthorp(revised 05/2000), established.
- Taxonomic class: Loamy, mixed, superactive, mesic, shallow Xeric Argidurids
- Rated with rule version 2026-09-28.1; the method is on the About page.