Westphalia soil
Wild-clay potential
Weak indication
Weak indication: no layer of Westphalia shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Westphalia soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Westphalia spot on the map
Rated from the USDA soil survey record for Westphalia and Dodon soils, 25 to 40 percent slopes (Prince George's County, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 8% clay.
- Lowers the potential Low engineering plasticity index (0): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 30 in (77 cm)).
- Note Typically starts within about 12 in (30 cm) of the surface.
- Note Few rock fragments (about 0% by volume).
Layer by layer
- TopsoilA A fine sandy loam layer about 0 to 6 in down: about 8% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
- Clay subsoilBt A fine sandy loam layer about 6 to 12 in down: about 14% clay, low plasticity when wet, strong brown when moist. Weak indication
- Sandy layerBCbest layer A loamy fine sand layer about 12 to 42 in down: about 8% clay, low plasticity when wet, brownish yellow when moist. Weak indication
- Sandy layerC A loamy fine sand layer about 42 to 72 in down: about 8% clay, low plasticity when wet, pale yellow when moist. Weak indication
What it looks like raw
The sandy layer (BC), 12 to 42 in down in the typical profile: brownish yellow (10YR 6/6); loamy fine sand; soft, very friable. Raw colour is not fired colour.
About the soil
- Parent material: loamy fluviomarine deposits.
- USDA family mineralogy: siliceous.
- USDA family particle-size class: coarse-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Maryland, in these survey areas: Prince George's County, Maryland.
By state: wild clay in Maryland.
USDA, distribution and extent: Coastal Plain of Maryland, New Jersey and Virginia. The Westphalia soils occur in large, almost continuous areas. They are of moderate extent.
USDA, geographic setting: Westphalia soils formed in Coastal Plain sediments of unconsolidated very fine and fine sands of uniform grain size. They are on uplands in the northern part of the inner Atlantic Coastal Plain. Areas are smooth to dissected. Slopes of 3 to 20 percent dominate but the slopes range from 0 to 50 percent. The climate is temperate and humid. Mean annual temperature is 45 to 57 degrees F., mean annual precipitation is 38 to 48 inches.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Christiana: Strong lead
- Howell: Strong lead
- Lenni: Strong lead
- Magnolia: Strong lead
- Aquasco: Promising
- Chillum: Promising
- Dodon: Promising
- Elkton: Promising
See it on the map
Open a Westphalia spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 45%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Westphalia and Dodon soils, 25 to 40 percent slopes, map unit WDF in Prince George's County, Maryland.
- Official Series Description: Westphalia(revised 11/2015), established.
- Taxonomic class: Coarse-loamy, siliceous, semiactive, mesic Inceptic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.