Umapine soil
Wild-clay potential
Weak indication
Weak indication: no layer of Umapine shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Umapine soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Umapine spot on the map
Rated from the USDA soil survey record for Umapine silt loam (Malheur County, Oregon, Northeastern Part) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 15% clay.
- Lowers the potential Low engineering plasticity index (3): little plastic behavior expected when wet.
- Lowers the potential The official series description calls the wet soil nonsticky and nonplastic.
- Note Thick enough to investigate (about 30 in (76 cm)).
- Note Typically starts about 30 in (76 cm) down; expect real digging or look for cuts and banks.
- Missing data Rock fragment content is not reported.
- Note USDA reports about 15% calcium carbonate; lime in a clay body deserves testing.
Layer by layer
- TopsoilAkn1 A silt loam layer about 0 to 2 in down: about 13% clay, low plasticity when wet, light brownish gray when moist. Weak indication
- TopsoilAkn2 A silt loam layer about 2 to 6 in down: about 13% clay, low plasticity when wet, light brownish gray when moist. Weak indication
- TopsoilAkn3 A silt loam layer about 6 to 11 in down: about 13% clay, low plasticity when wet, light brownish gray when moist. Weak indication
- Sandy layerBk1 A silt loam layer about 11 to 23 in down: about 15% clay, low plasticity when wet, grayish brown when moist. Weak indication
- Sandy layerBk2 A silt loam layer about 23 to 30 in down: about 15% clay, low plasticity when wet, gray when moist. Weak indication
- Sandy layerBk3best layer A silt loam layer about 30 to 60 in down: about 15% clay, low plasticity when wet, grayish brown when moist. Weak indication
What it looks like raw
The sandy layer (Bk3), 30 to 60 in down in the typical profile: grayish brown (10YR 5/2) dry, dark grayish brown (10YR 4/2) moist; slightly hard, friable, nonsticky and nonplastic. Raw colour is not fired colour.
About the soil
- Parent material: alluvium.
- USDA family particle-size class: coarse-silty.
- Drainage: somewhat poorly drained.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Oregon, in these survey areas: Malheur County, Oregon, Northeastern Part.
By state: wild clay in Oregon.
USDA, distribution and extent: Central and southeastern Washington and eastern Oregon; MLRAs 7 and 8; moderate extent
USDA, geographic setting: Elevation--75 to 1075 m
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- McLoughlin: Promising
- Frohman: Weak indication
- Garbutt: Weak indication
- Notus: Weak indication
- Nyssa: Weak indication
- Owyhee: Weak indication
- Turbyfill: Weak indication
- Alyan: Strong lead(same state)
See it on the map
Open a Umapine spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Umapine silt loam, map unit 34 in Malheur County, Oregon, Northeastern Part.
- Official Series Description: Umapine(revised 09/2019), established.
- Taxonomic class: Coarse-silty, mixed, superactive, calcareous, mesic Typic Halaquepts
- Rated with rule version 2026-09-28.1; the method is on the About page.