Turbyfill soil
Wild-clay potential
Weak indication
Weak indication: no layer of Turbyfill shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Turbyfill soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Turbyfill spot on the map
Rated from the USDA soil survey record for Turbyfill fine sandy loam, 0 to 2 percent slopes (Malheur County, Oregon, Northeastern Part) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 12% clay.
- Lowers the potential Low engineering plasticity index (3): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 23 in (58 cm)).
- Note Typically starts about 37 in (94 cm) down; expect real digging or look for cuts and banks.
- Note Few rock fragments (about 5% by volume).
- Note USDA reports about 10% calcium carbonate; lime in a clay body deserves testing.
Layer by layer
- TopsoilAp A fine sandy loam layer about 0 to 6 in down: about 12% clay, low plasticity when wet, light brownish gray when moist. Weak indication
- Sandy layerBk1 A fine sandy loam layer about 6 to 20 in down: about 12% clay, low plasticity when wet, light brownish gray when moist. Weak indication
- Sandy layerBk2 A fine sandy loam layer about 20 to 37 in down: about 12% clay, low plasticity when wet, light gray when moist. Weak indication
- Sandy layerBk3best layer A fine sandy loam layer about 37 to 60 in down: about 12% clay, low plasticity when wet, light gray when moist. Weak indication
What it looks like raw
The sandy layer (Bk3), 37 to 60 in down in the typical profile: light gray (10YR 7/2), brown (10YR 4/3) moist; soft, very friable. Raw colour is not fired colour.
About the soil
- Parent material: alluvium.
- USDA family particle-size class: coarse-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 12 map units in Idaho, Oregon, in these survey areas: Ada County, Idaho; Canyon Area, Idaho; Malheur County, Oregon, Northeastern Part; Malheur County, Oregon, Northern Part.
By state: wild clay in Idaho,wild clay in Oregon.
USDA, distribution and extent: Southern Idaho and southeastern Oregon. The soils are moderately extensive.
USDA, geographic setting: The soils are in alluvial fans and terraces and in alluvium on basalt plains at elevations of 2,000 to 4,500 feet. Slopes are predominantly less than 7 percent and range from 0 to 35 percent. The soils formed in silty alluvium or eolian deposits. The climate is middle latitude steppe (Trewartha's Modified Koppen system) and has dry summers. The frost free period is 110 to 160 days, and mean annual precipitation is 7 to 11 inches including 0.5 to 2 feet of snow. The mean annual temperature is 47 to 52 degrees F.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Aldape: Strong lead
- Aradaran: Strong lead
- Bowns: Strong lead
- Breadloaf: Strong lead
- Brent: Strong lead
- Castlerock: Strong lead
- Catchell: Strong lead
- Chardoton: Strong lead
See it on the map
Open a Turbyfill spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 80%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Turbyfill fine sandy loam, 0 to 2 percent slopes, map unit 33A in Malheur County, Oregon, Northeastern Part.
- Official Series Description: Turbyfill(revised 10/2002), established.
- Taxonomic class: Coarse-loamy, mixed, superactive, calcareous, mesic Xeric Torriorthents
- Rated with rule version 2026-09-28.1; the method is on the About page.