Shalcar soil
Wild-clay potential
Promising
Promising: a loamy layer with some clay typically about 32 to 60 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Shalcar soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Shalcar spot on the map
Rated from the USDA soil survey record for Shalcar muck (Kitsap County Area, Washington) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clay-enriched layer: a stratified loamy sand to silty clay loam texture in the fine-earth portion.
- Note No clay percentage is reported; the clay level is read from the USDA texture class only.
- Note Moderate engineering plasticity index (10).
- Note The official series description calls the wet soil slightly sticky and slightly plastic.
- Note Thick enough to investigate (about 28 in (71 cm)).
- Note Typically starts about 32 in (81 cm) down; expect real digging or look for cuts and banks.
- Missing data Rock fragment content is not reported.
Layer by layer
- Organic top layerOa1 An organic top layer about 0 to 8 in down, not a clay body. Weak indication
- Organic top layerOa2 An organic top layer about 8 to 32 in down, not a clay body. Weak indication
- Loamy layerH3best layer A stratified loamy sand to silty clay loam layer about 32 to 60 in down: moderate plasticity when wet, very dark grayish brown when moist. Promising
What it looks like raw
The loamy layer (H3), 32 to 60 in down in the typical profile: very dark grayish brown (10YR 3/2) moist, grayish brown (2.5Y 5/2) dry; slightly hard, friable, slightly sticky and slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: woody organic material over alluvium.
- USDA family mineralogy: mixed.
- USDA family particle-size class: loamy.
- Drainage: very poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Washington, in these survey areas: Kitsap County Area, Washington.
By state: wild clay in Washington.
USDA, distribution and extent: Western Washington, west of the Cascade Mountains; MLRA 2; moderate extent
USDA, geographic setting: Elevation--0 to 215 m
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bellingham: Strong lead
- McKenna: Promising
- Kitsap: Possible
- Alderwood: Weak indication
- Belfast: Weak indication
- Harstine: Weak indication
- Indianola: Weak indication
- Kapowsin: Weak indication
See it on the map
Open a Shalcar spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Shalcar muck, map unit 50 in Kitsap County Area, Washington.
- Official Series Description: Shalcar(revised 04/2017), established.
- Taxonomic class: Loamy, mixed, euic, mesic Terric Haplosaprists
- Rated with rule version 2026-09-28.1; the method is on the About page.