Kitsap soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 4 to 32 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Kitsap soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Kitsap gravelly loam, 0 to 15 percent slopes (Jefferson County Area, Washington) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 26% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (12.5).
- Raises the potential The official series description calls the wet soil moderately sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 28 in (71 cm)).
- Note Typically starts within about 4 in (10 cm) of the surface.
- Note Few rock fragments (about 5% by volume).
Layer by layer
- Sandy layerH1 A gravelly loam layer about 0 to 4 in down: about 10% clay, low plasticity when wet, grayish brown when moist. Weak indication
- Loamy layerH2best layer A silt loam layer about 4 to 32 in down: about 26% clay, moderate plasticity when wet, light gray when moist. Possible
- Loamy layerH3 A stratified silt loam to silty clay loam to gravelly silty clay loam layer about 32 to 60 in down: about 28% clay, moderate plasticity when wet, light brownish gray when moist. Possible
What it looks like raw
The loamy layer (H2), 4 to 32 in down in the typical profile: light gray (2.5Y 7/2) dry, grayish brown (2.5Y 5/2) moist; hard, firm, moderately sticky and moderately plastic. Raw colour is not fired colour.
About the soil
- Parent material: lacustrine deposits and/or marine deposits.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-silty.
- Drainage: moderately well drained.
Where it is mapped
Seen on the map as the most common soil in 9 map units in Washington, in these survey areas: Jefferson County Area, Washington; Kitsap County Area, Washington.
By state: wild clay in Washington.
USDA, distribution and extent: Western Washington; MLRA 2 moderate extent.
USDA, geographic setting: Elevation--0 to 165 m
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bellingham: Strong lead
- Quilcene: Strong lead
- McKenna: Promising
- Shalcar: Promising
- Wapato: Promising
- Lummi: Possible
- Alderwood: Weak indication
- Belfast: Weak indication
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Kitsap gravelly loam, 0 to 15 percent slopes, map unit KsC in Jefferson County Area, Washington.
- Official Series Description: Kitsap(revised 10/2018), established.
- Taxonomic class: Fine-silty, isotic, nonacid, mesic Aeric Endoaquepts
- Rated with rule version 2026-09-28.1; the method is on the About page.