Quilcene soil
Wild-clay potential
Strong lead
Strong lead: a clayey layer typically about 6 to 19 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Quilcene soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Quilcene spot on the map
Rated from the USDA soil survey record for Quilcene silt loam, 0 to 15 percent slopes (Jefferson County Area, Washington) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Raises the potential Clayey layer: about 35% clay in the fine-earth portion.
- Raises the potential High engineering plasticity index (25): USDA's estimate suggests plastic behavior when wet.
- Raises the potential The official series description calls the wet soil moderately sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 13 in (33 cm)).
- Note Typically starts within about 6 in (15 cm) of the surface.
- Note Few rock fragments (about 12% by volume).
- Note High shrink-swell (linear extensibility about 7.5%): often very plastic, and prone to cracking as it dries.
Layer by layer
- Loamy layerH1 A silt loam layer about 0 to 6 in down: about 20% clay, moderate plasticity when wet, dark grayish brown when moist. Possible
- Clay-rich layerH2best layer A silty clay loam layer about 6 to 19 in down: about 35% clay, high plasticity when wet, brown when moist. Strong lead
- Clay-rich layerH3 A gravelly clay layer about 19 to 27 in down: about 43% clay, high plasticity when wet, yellowish brown when moist. Promising
- BedrockH4 Weathered bedrock about 27 to 31 in down: no clay layer to dig. Weak indication
What it looks like raw
The clay-rich layer (H2), 6 to 19 in down in the typical profile: brown (10YR 5/3), and brown (7.5YR 5/4), pinkish gray (7.5YR 7/2) dry; slightly hard, friable, moderately sticky, moderately plastic. Raw colour is not fired colour.
About the soil
- Parent material: colluvium and residuum from sandstone and shale.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine.
- Drainage: moderately well drained.
- Paralithic bedrock typically about 27 in (68 cm) down.
Where it is mapped
Seen on the map as the most common soil in 3 map units in Washington, in these survey areas: Jefferson County Area, Washington.
By state: wild clay in Washington.
USDA, distribution and extent: Northwestern Washington. Series is of small extent.
USDA, geographic setting: The Quilcene soils occur on undulating to steep uplands at elevations of near sea level to about 800 feet. The regolith consists of weathered shale and sandstone with some modification by glacial action. These soils occur in a subhumid maritime climate with summers relatively dry and cool and winters wet and mild. The annual precipitation ranges from 30 to 45 inches. The average January temperature is 40 degrees F.; the average July temperature is 60 degrees F.; and the annual frost free growing season is 170 to 190 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Wapato: Promising
- Kitsap: Possible
- Lummi: Possible
- Ahl: Weak indication
- Alderwood: Weak indication
- Beausite: Weak indication
- Belfast: Weak indication
- Carlsborg: Weak indication
See it on the map
Open a Quilcene spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
- Parts of the Official Series Description could not be interpreted; open the original for the complete text.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Quilcene silt loam, 0 to 15 percent slopes, map unit QuC in Jefferson County Area, Washington.
- Official Series Description: Quilcene(revised 01/2000), established.
- Taxonomic class: Fine, isotic, mesic Aquic Dystroxerepts
- Rated with rule version 2026-09-28.1; the method is on the About page.