Belfast soil
Wild-clay potential
Weak indication
Weak indication: no layer of Belfast shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Belfast soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Belfast spot on the map
Rated from the USDA soil survey record for Belfast fine sandy loam (Jefferson County Area, Washington) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 10% clay.
- Lowers the potential Low engineering plasticity index (2.5): little plastic behavior expected when wet.
- Note The official series description calls the wet soil slightly plastic.
- Note Thick enough to investigate (about 46 in (116 cm)).
- Note Typically starts within about 14 in (36 cm) of the surface.
- Note Few rock fragments (about 9% by volume).
Layer by layer
- Sandy layerH1 A fine sandy loam layer about 0 to 6 in down: about 10% clay, low plasticity when wet, very dark grayish brown when moist. Weak indication
- Sandy layerH2 A silt loam layer about 6 to 14 in down: about 10% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
- Sandy layerH3best layer A stratified loamy sand to silt loam layer about 14 to 60 in down: about 10% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
What it looks like raw
The sandy layer (H3), 14 to 60 in down in the typical profile: dark grayish brown (2.5Y 4/2), light brownish gray (2.5Y 6/2) dry; slightly hard, friable and slightly plastic. Raw colour is not fired colour.
About the soil
- Parent material: alluvium.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 3 map units in Washington, in these survey areas: Jefferson County Area, Washington; Kitsap County Area, Washington.
By state: wild clay in Washington.
USDA, distribution and extent: Northwestern Washington. The series is of small extent.
USDA, geographic setting: Belfast soils are on nearly level flood plains at elevations of 20 to 600 feet. They formed in stratified alluvium. The climate is cool and dry in summer and mild and wet in winter. Annual precipitation ranges from 50 to 70 inches. Average January temperature is about 40 degrees F.; average July temperature is about 60 degrees F. The frost-free season is about 170 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bellingham: Strong lead
- Quilcene: Strong lead
- McKenna: Promising
- Shalcar: Promising
- Wapato: Promising
- Kitsap: Possible
- Lummi: Possible
- Alderwood: Weak indication
See it on the map
Open a Belfast spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 95%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Belfast fine sandy loam, map unit Bf in Jefferson County Area, Washington.
- Official Series Description: Belfast(revised 10/2002), established.
- Taxonomic class: Coarse-loamy, isotic, nonacid, mesic Aquandic Xerofluvents
- Rated with rule version 2026-09-28.1; the method is on the About page.