Lummi soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 29 to 60 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Lummi soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Lummi silt loam (Jefferson County Area, Washington) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 23% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (10).
- Raises the potential The official series description calls the wet soil slightly sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 31 in (78 cm)).
- Note Typically starts about 29 in (74 cm) down; expect real digging or look for cuts and banks.
- Note Few rock fragments (about 3% by volume).
Layer by layer
- Loamy layerH1 A silt loam layer about 0 to 10 in down: about 24% clay, moderate plasticity when wet, dark brown when moist. Possible
- Loamy layerH2 A silt loam layer about 10 to 29 in down: about 23% clay, moderate plasticity when wet, dark gray when moist. Possible
- Loamy layerH3best layer A silt loam layer about 29 to 60 in down: about 23% clay, moderate plasticity when wet, very dark gray when moist. Possible
What it looks like raw
The loamy layer (H3), 29 to 60 in down in the typical profile: very dark gray (5YR 3/1), gray (5Y 5/1) dry; hard, firm, slightly sticky and plastic. Raw colour is not fired colour.
About the soil
- Parent material: alluvium and/or marine deposits.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-silty.
- Drainage: poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 1 map unit in Washington, in these survey areas: Jefferson County Area, Washington.
By state: wild clay in Washington.
USDA, distribution and extent: Northwestern Washington. This series is of small extent.
USDA, geographic setting: Lummi soils are on flood plains near estuaries and tidal salt marshes at elevations of near sea level to 50 feet. Slopes are 0 to 3 percent. They formed in marine sediments and alluvium. The soils are in a mild marine climate and have cool, dry summers and cool, moist winters. Mean annual precipitation is 25 to 50 inches. Average January temperature is about 38 degrees F., average July temperature is about 60 degrees F., and the mean annual temperature is about 49 degrees F. Frost-free season is 170 to 200 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Quilcene: Strong lead
- Wapato: Promising
- Kitsap: Possible
- Ahl: Weak indication
- Alderwood: Weak indication
- Beausite: Weak indication
- Belfast: Weak indication
- Carlsborg: Weak indication
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Lummi silt loam, map unit Lu in Jefferson County Area, Washington.
- Official Series Description: Lummi(revised 10/2002), established.
- Taxonomic class: Fine-silty, mixed, superactive, mesic Fluvaquentic Endoaquolls
- Rated with rule version 2026-09-28.1; the method is on the About page.