Reybold soil
Wild-clay potential
Possible
Possible: a clay-enriched layer typically about 6 to 27 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Reybold soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Reybold spot on the map
Rated from the USDA soil survey record for Reybold loam, gravelly subsoil, 2 to 5 percent slopes (Charles County, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 21% clay. It may need settling or refining to become a clay body.
- Note USDA labels this a "Bt1" horizon: a subsoil layer where clay has accumulated.
- Note Moderate engineering plasticity index (10).
- Raises the potential The official series description calls the wet soil moderately sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 21 in (54 cm)).
- Note Typically starts within about 6 in (15 cm) of the surface.
- Note Few rock fragments (about 10% by volume).
Layer by layer
- TopsoilAp A loam layer about 0 to 6 in down: about 17% clay, low plasticity when wet, dark yellowish brown when moist. Weak indication
- Clay subsoilBt1best layer A sandy clay loam layer about 6 to 27 in down: about 21% clay, moderate plasticity when wet, dark yellowish brown when moist. Possible
- Clay subsoilBt2 A gravelly sandy clay loam layer about 27 to 33 in down: about 27% clay, moderate plasticity when wet, yellowish brown when moist. Possible
- Sandy layer2BC A very gravelly sandy loam layer about 33 to 62 in down: about 11% clay, low plasticity when wet, yellowish brown when moist. Weak indication
What it looks like raw
The clay subsoil (Bt1), 6 to 27 in down in the typical profile: dark yellowish brown (10YR 4/6); silt loam; friable, moderately sticky; moderately plastic. Raw colour is not fired colour.
About the soil
- Parent material: loamy fluviomarine deposits.
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-loamy.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 6 map units in Delaware, Maryland, in these survey areas: Cecil County, Maryland; Charles County, Maryland; New Castle County, Delaware.
By state: wild clay in Delaware,wild clay in Maryland.
USDA, distribution and extent: Distribution: Coastal plain areas of Maryland and Delaware
USDA, geographic setting: Landscape: Coastal plain
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Lenni: Strong lead
- Montalto: Strong lead
- Watchung: Strong lead
- Christiana: Strong lead
- Magnolia: Strong lead
- Talleyville: Strong lead
- Nanticoke: Promising
- Baile: Promising
See it on the map
Open a Reybold spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 80%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Reybold loam, gravelly subsoil, 2 to 5 percent slopes, map unit RgB in Charles County, Maryland.
- Official Series Description: Reybold(revised 04/2007), established.
- Taxonomic class: Fine-loamy, mixed, semiactive, mesic Typic Hapludults
- Rated with rule version 2026-09-28.1; the method is on the About page.