Ragnar soil
Wild-clay potential
Weak indication
Weak indication: no layer of Ragnar shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Ragnar soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Ragnar fine sandy loam, 0 to 6 percent slopes (Kitsap County Area, Washington) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 3% clay.
- Lowers the potential Low engineering plasticity index (0): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 39 in (99 cm)).
- Note Typically starts within about 21 in (53 cm) of the surface.
- Note Few rock fragments (about 6% by volume).
Layer by layer
- Sandy layerH1 An ashy fine sandy loam layer about 0 to 4 in down: about 10% clay, low plasticity when wet, very dark grayish brown when moist. Weak indication
- Sandy layerH2 An ashy fine sandy loam layer about 4 to 21 in down: about 10% clay, low plasticity when wet, dark yellowish brown when moist. Weak indication
- Sandy layerH3best layer A loamy sand layer about 21 to 60 in down: about 3% clay, low plasticity when wet, olive brown when moist. Weak indication
What it looks like raw
The sandy layer (H3), 21 to 60 in down in the typical profile: olive brown (2.5Y 4/4), yellowish brown (10YR 5/3) dry; loose. Raw colour is not fired colour.
About the soil
- Parent material: glacial outwash with some volcanic ash in the upper part.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy over sandy or sandy-skeletal.
- Drainage: well drained.
Where it is mapped
Seen on the map as the most common soil in 4 map units in Washington, in these survey areas: Kitsap County Area, Washington.
By state: wild clay in Washington.
USDA, distribution and extent: Northwestern Washington. This series is moderately extensive.
USDA, geographic setting: These soils are on esker and kame like relief along the edges of major valleys at elevations of 300 to 1,000 feet. Slopes are 0 to 70 percent. The soils formed in glacial outwash. They have cool, dry summers and mild, wet winters. The average annual precipitation ranges from 35 to 65 inches, most of which falls between October and April. Some snow falls in winter. The average January temperature is about 38 degrees F.; the average July temperature is 66 degree F.; and the frost free season ranges from 150 to 212 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Bellingham: Strong lead
- McKenna: Promising
- Shalcar: Promising
- Kitsap: Possible
- Alderwood: Weak indication
- Belfast: Weak indication
- Harstine: Weak indication
- Indianola: Weak indication
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Ragnar fine sandy loam, 0 to 6 percent slopes, map unit 44 in Kitsap County Area, Washington.
- Official Series Description: Ragnar(revised 01/2000), established.
- Taxonomic class: Coarse-loamy over sandy or sandy-skeletal, isotic over mixed, mesic Vitrandic Dystroxerepts
- Rated with rule version 2026-09-28.1; the method is on the About page.