Potobac soil
Wild-clay potential
Weak indication
Weak indication: no layer of Potobac shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Potobac soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Open a Potobac spot on the map
Rated from the USDA soil survey record for Potobac-Issue complex, frequently flooded (Charles County, Maryland) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 11% clay.
- Lowers the potential Low engineering plasticity index (5): little plastic behavior expected when wet.
- Note The official series description calls the wet soil nonsticky and slightly plastic.
- Note Thick enough to investigate (about 22 in (57 cm)).
- Note Typically starts within about 17 in (43 cm) of the surface.
- Note Few rock fragments (about 10% by volume).
Layer by layer
- TopsoilA A loam layer about 0 to 8 in down: about 23% clay, moderate plasticity when wet, dark brown when moist. Weak indication
- Loamy layerBg A loam layer about 8 to 17 in down: about 18% clay, low plasticity when wet, olive gray when moist. Weak indication
- Sandy layerCg1best layer A sandy loam layer about 17 to 39 in down: about 11% clay, low plasticity when wet, dark grayish brown when moist. Weak indication
- Sandy layerCg2 A very gravelly coarse sand layer about 39 to 59 in down: about 2% clay, low plasticity when wet, grayish brown when moist. Weak indication
What it looks like raw
The sandy layer (Cg1), 17 to 39 in down in the typical profile: dark grayish brown (2.5Y 4/2); sandy loam; nonsticky, slightly plastic. Raw colour is not fired colour.
About the soil
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy.
- Drainage: poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 2 map units in Maryland, in these survey areas: Charles County, Maryland; Prince George's County, Maryland.
By state: wild clay in Maryland.
USDA, distribution and extent: Distribution: Floodplains of the mid-Atlantic Coastal Plain of Maryland; MLRA 149A.
USDA, geographic setting: Landscape: Coastal plain
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Lenni: Strong lead
- Magnolia: Strong lead
- Christiana: Strong lead
- Howell: Strong lead
- Elkton: Promising
- Liverpool: Promising
- Nanticoke: Promising
- Piccowaxen: Promising
See it on the map
Open a Potobac spot on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 70%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Potobac-Issue complex, frequently flooded, map unit Pu in Charles County, Maryland.
- Official Series Description: Potobac(revised 06/2007), established.
- Taxonomic class: Coarse-loamy, mixed, active, nonacid, mesic Fluvaquentic Endoaquepts
- Rated with rule version 2026-09-28.1; the method is on the About page.