Melvin soil
Wild-clay potential
Possible
Possible: a loamy layer with some clay typically about 30 to 62 in below the surface.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Melvin soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Melvin silt loam (District of Columbia) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 24% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (12.5).
- Note Thick enough to investigate (about 32 in (81 cm)).
- Note Typically starts about 30 in (76 cm) down; expect real digging or look for cuts and banks.
- Note Few rock fragments (about 10% by volume).
Layer by layer
- Sandy layerH1 A silt loam layer about 0 to 9 in down: about 15% clay, moderate plasticity when wet, dark grayish brown when moist. Weak indication
- Loamy layerH2 A silt loam layer about 9 to 30 in down: about 24% clay, moderate plasticity when wet, light brownish gray when moist. Possible
- Loamy layerH3best layer A silt loam layer about 30 to 62 in down: about 24% clay, moderate plasticity when wet, light brownish gray when moist. Possible
What it looks like raw
The loamy layer (H3), 30 to 62 in down in the typical profile: light brownish gray (10YR 6/2); firm. Raw colour is not fired colour.
About the soil
- USDA family mineralogy: mixed.
- USDA family particle-size class: fine-silty.
- Drainage: poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 4 map units in District of Columbia, Maryland, Pennsylvania, in these survey areas: Baltimore County, Maryland; Centre County, Pennsylvania; District of Columbia; Lebanon County, Pennsylvania.
By state: wild clay in District of Columbia,wild clay in Maryland,wild clay in Pennsylvania.
USDA, distribution and extent: Indiana, Kentucky, Maryland, Ohio, Pennsylvania, Tennessee, Virginia, West Virginia, and possibly Arkansas and Missouri. The series is of large extent.
USDA, geographic setting: Melvin soils are on nearly level to depressed parts of flood plains and in upland depressions. Slopes range from 0 to 2 percent. These soils formed in silty alluvium derived from soils formed from limestone, shale, siltstone, sandstone, and loess. Near the type location the mean annual temperature ranges from 53 to 59.4 degrees F., and mean annual precipitation ranges from 40 to 53.9 inches.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Christiana: Strong lead
- Dunning: Strong lead
- Hagerstown: Strong lead
- Watchung: Strong lead
- Benevola: Strong lead
- Cumberstone: Strong lead
- Hublersburg: Strong lead
- Jackland: Strong lead
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 100%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Melvin silt loam, map unit Mp in District of Columbia.
- Official Series Description: Melvin(revised 11/2007), established.
- Taxonomic class: Fine-silty, mixed, active, nonacid, mesic Fluvaquentic Endoaquepts
- Rated with rule version 2026-09-28.1; the method is on the About page.