Melton soil
Wild-clay potential
Weak indication
Weak indication: no layer of Melton shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Melton soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Melton loam, frequently flooded, 0 to 2 percent slopes (Adams-Washington Area, Parts of Adams and Washington Counties, Idaho) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Lowers the potential Too little clay to be a clay body on its own: about 6% clay.
- Lowers the potential Low engineering plasticity index (5): little plastic behavior expected when wet.
- Note Thick enough to investigate (about 27 in (68 cm)).
- Note Typically starts about 33 in (84 cm) down; expect real digging or look for cuts and banks.
- Lowers the potential High rock content (about 41% by volume) lowers its practical promise; the clay percentage applies only to the fine earth between the rocks.
Layer by layer
- TopsoilA A loam layer about 0 to 12 in down: about 22% clay, moderate plasticity when wet, dark grayish brown when moist. Weak indication
- Loamy layerCg1 A loam layer about 12 to 16 in down: about 22% clay, moderate plasticity when wet, grayish brown when moist. Weak indication
- Sandy layerCg2 A gravelly sandy loam layer about 16 to 33 in down: about 9% clay, moderate plasticity when wet, brown when moist. Weak indication
- Sandy layerCbest layer A very cobbly loamy sand layer about 33 to 60 in down: about 6% clay, low plasticity when wet, cobbly till consisting of mixed acid and basic igneous cobblestones with light brownish gray when moist. Weak indication
What it looks like raw
The sandy layer (C), 33 to 60 in down in the typical profile: cobbly till consisting of mixed acid and basic igneous cobblestones with light brownish gray (10YR 6/2), and pale brown (10YR 6/3), dark grayish brown (10YR 4/2), and brown (10YR 4/3) moist. Raw colour is not fired colour.
About the soil
- Parent material: alluvium and/or outwash derived from granite.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy.
- Drainage: poorly drained.
- Rated hydric (wetland) soil; often saturated and protected.
Where it is mapped
Seen on the map as the most common soil in 5 map units in Idaho, in these survey areas: Adams-Washington Area, Parts of Adams and Washington Counties, Idaho; South Idaho Forests, Idaho; Valley Area, Idaho, Parts of Adams and Valley Counties.
By state: wild clay in Idaho.
USDA, distribution and extent: In the cold high mountain valleys, mainly in Valley County, Idaho. The soil is inextensive.
USDA, geographic setting: Melton soils are on stream bottoms. Slopes are 0 to 3 percent. The soils formed in alluvium from glacial outwash. Elevations are 3,800 to 5,100 feet. Average annual precipitation is 22 to 24 inches. Average January temperature is 20 degrees F.; average July temperature is 64 degrees F. Average annual temperature is 38 degrees to 40 degrees F. Frost-free season is about 60 to 75 days.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Cabarton: Strong lead
- Sudpeak: Strong lead
- Blackwell: Promising
- Swede: Promising
- Catherine: Promising
- Culdecole: Promising
- Nisula: Promising
- Ticanot: Possible
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 95%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Melton loam, frequently flooded, 0 to 2 percent slopes, map unit 139 in Adams-Washington Area, Parts of Adams and Washington Counties, Idaho.
- Official Series Description: Melton(revised 11/2002), established.
- Taxonomic class: Fine-loamy over sandy or sandy-skeletal, mixed, superactive, acid Humic Cryaquepts
- Rated with rule version 2026-09-28.1; the method is on the About page.