Mardin soil
Wild-clay potential
Weak indication
Weak indication: no layer of Mardin shows strong clay evidence in the USDA data.
A level means "worth investigating". It never confirms usable pottery clay.
This page is about Mardin soil in general. Whether it lies under a particular spot, and how deep its clay layer sits there, depends on the spot: tap it on the free Wild Clay Archive map at wildclayarchive.com.
Rated from the USDA soil survey record for Mardin channery silt loam, 3 to 8 percent slopes (Delaware County, New York) and the Official Series Description. Depths are typical for the series, not measured at any spot.
Why this level
- Note Loamy layer with some clay: about 18% clay. It may need settling or refining to become a clay body.
- Note Moderate engineering plasticity index (12).
- Raises the potential The official series description calls the wet soil slightly sticky and moderately plastic (a field observation, not a ceramic test).
- Note Thick enough to investigate (about 21 in (54 cm)).
- Note Typically starts about 36 in (91 cm) down; expect real digging or look for cuts and banks.
- Lowers the potential Noticeable rock fragments (about 34% by volume); screening would be needed and the clay percentage applies to the fine earth only.
Layer by layer
- TopsoilAp A channery silt loam layer about 0 to 8 in down: about 14% clay, moderate plasticity when wet, brown when moist. Weak indication
- Sandy layerBE A channery silt loam layer about 8 to 12 in down: about 12% clay, moderate plasticity when wet, light olive brown when moist. Weak indication
- Sandy layerBw1 A channery silt loam layer about 12 to 16 in down: about 14% clay, moderate plasticity when wet, yellowish brown when moist. Weak indication
- Sandy layerBw2 A channery silt loam layer about 16 to 20 in down: about 14% clay, moderate plasticity when wet, brown when moist. Weak indication
- Loamy layerBx1 A channery silt loam layer about 20 to 36 in down: about 18% clay, moderate plasticity when wet, dark yellowish brown when moist. Weak indication
- Loamy layerBx2best layer A channery silt loam layer about 36 to 57 in down: about 18% clay, moderate plasticity when wet, olive brown when moist. Weak indication
- Sandy layerC A channery silt loam layer about 57 to 72 in down: about 16% clay, moderate plasticity when wet, olive brown when moist. Weak indication
What it looks like raw
The loamy layer (Bx2), 36 to 57 in down in the typical profile: olive brown (2.5Y 4/4); channery silt loam; very firm, slightly sticky, moderately plastic; brittle. Raw colour is not fired colour.
About the soil
- Parent material: loamy till.
- USDA family mineralogy: mixed.
- USDA family particle-size class: coarse-loamy.
- Drainage: moderately well drained.
Where it is mapped
Seen on the map as the most common soil in 11 map units in New York, in these survey areas: Delaware County, New York; Otsego County, New York; Schoharie County, New York.
By state: wild clay in New York.
USDA, distribution and extent: Southern New York and northern Pennsylvania. MLRA 101, 139, 140, and 144A. The series is extensive.
USDA, geographic setting: Mardin soils are nearly level to very steep with slopes ranging from 0 through 50 percent. These soils developed in till, and are on slightly convex parts of dissected glaciated uplands. Mean annual temperature ranges 6 to 11 degrees C (43 through 52 degrees F). Mean annual precipitation ranges from 795 through 1725 millimeters (31 through 68 inches), and mean annual frost-free season ranges from 105 through 180 days. These soils generally occur at elevations between 100 and 670 meters (328 and 2,198 feet), but have been mapped as high as 750 meters (2,460 feet) in some areas.
Other soils near it
Rated soils mapped in the same counties, stronger leads first.
- Lakemont: Strong lead
- Phelps: Strong lead
- Holly: Promising
- Alden: Possible
- Canandaigua: Possible
- Bath: Weak indication
- Lordstown: Weak indication
- Volusia: Weak indication
See it on the map
Soil information does not grant access or permission to dig. Verify ownership, local rules, and permission before visiting or collecting.
Important uncertainties
- A component percentage (about 85%) estimates how much of the whole map unit this component covers; it is not the chance that it lies under a spot you look up on the map.
- Layer depths and thicknesses are typical values for the series; the actual profile at a spot can differ substantially.
- Clay percentages describe the fine-earth fraction (particles under 2 mm); rock fragments are reported separately.
- USDA words like "sticky" and "plastic" are field observations on wet soil, not tests of forming, drying, or firing behavior.
Sources
- USDA Soil Data Access (SSURGO): the survey record for Mardin channery silt loam, 3 to 8 percent slopes, map unit MdB in Delaware County, New York.
- Official Series Description: Mardin(revised 09/2017), established.
- Taxonomic class: Coarse-loamy, mixed, active, mesic Typic Fragiudepts
- Rated with rule version 2026-09-28.1; the method is on the About page.